Optimizing Size and Number Density of Al3Zr Dispersoids in Al-Zn-Mg-Cu Alloys

被引：2
|
作者：
Honaramooz, Mohammad Taha [1 ,3 ]
Morak, Roland [2 ]
Paris, Oskar [1 ]
机构：
[1] Univ Leoben, Chair Phys, Dept Phys Mech & Elect Engn, Franz Josef Str 18, A-8700 Leoben, Austria
[2] AMAG Rolling GmbH, Ctr Mat Innovat, R&D Mat Sci CMI, Postfach 32, A-5282 Ranshofen, Austria
[3] Constantia Teich GmbH, Aluminum Div, R&D Competence Ctr Aluminum, Mulhlhofen 4, A-3205 Weinburg, Austria
来源：
ADVANCED ENGINEERING MATERIALS | 2024年 / 26卷 / 19期
关键词：
aluminum alloys; homogenizations; in situ small-angle X-ray scattering; phase transformation kinetics; ANGLE X-RAY; ZR-TI ALLOYS; PRECIPITATION EVOLUTION; BEHAVIOR; KINETICS; HOMOGENIZATION; NUCLEATION; SCATTERING; PHASE;
D O I：
10.1002/adem.202400353
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
The formation and temporal evolution of Al3Zr dispersoids in an Al-Zn-Mg-Cu alloy is investigated by in situ small-angle X-ray scattering during different homogenization treatments. The aim is to determine the most effective homogenization parameters for obtaining a high number density and small size of the dispersoids. Nucleation of the dispersoids is found to start above 400 degrees C and is boosted after isothermal holding at 425 degrees C. Regardless of the detailed homogenization profile, coarsening of the dispersoids is not observed below 450 degrees C. The results demonstrate that decreasing the heating rate, prolonging the first isothermal step, or increasing the number of steps are all beneficial regarding an increase of both, the volume fraction, and the number density of the dispersoids. Among the four investigated homogenization profiles, the one with decreasing the heating rate shows the highest impact.
引用
收藏
页数：7
相关论文
共 50 条
  • [41] The influence of Al3Zr dispersoids on the recrystallization of hot-deformed AA 7010 alloys
    Bruce Morere
    Ravi Shahani
    Claire Maurice
    Julian Driver
    Metallurgical and Materials Transactions A, 2001, 32 : 625 - 632
  • [42] The influence of Al3Zr dispersoids on the recrystallization of hot-deformed AA 7010 alloys
    Morere, B
    Maurice, C
    Shahani, R
    Driver, J
    METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2001, 32 (03): : 625 - 632
  • [43] Precipitation in Al-Zn-Mg-(Cu,Zr) alloys
    Chinh, NQ
    Kovacs, Z
    Reich, L
    Szekely, F
    Illy, J
    Lendvai, J
    ZEITSCHRIFT FUR METALLKUNDE, 1997, 88 (08): : 607 - 611
  • [44] Precipitation in Al-Zn-Mg-(Cu, Zr) Alloys
    Department of General Physics, Eötvös University, Budapest, VIII, P.O.B. 323, Budapest
    H-1145, Hungary
    Int. J. Mater. Res., 8 (607-611):
  • [45] EXTRUSION OF AL-ZN-MG-CU-ZR ALLOYS
    BALASUBRAMANIAN, PK
    MATERIALS SCIENCE AND TECHNOLOGY, 1985, 1 (06) : 470 - 474
  • [46] Precipitation in Al-Zn-Mg-(Cu,Zr) alloys
    Chinh, Nguyen Quang
    Kovacs, Zsolt
    Reich, Lajos
    Szekely, Ferenc
    Illy, Judit
    Lendvai, Janos
    Zeitschrift fuer Metallkunde/Materials Research and Advanced Techniques, 1997, 88 (08): : 607 - 611
  • [47] FURTHER PRECIPITATION REACTIONS ASSOCIATED WITH BETA-'(AL3ZR) PARTICLES IN AL-LI-CU-MG-ZR ALLOYS
    TITE, CNJ
    GREGSON, PJ
    PITCHER, PD
    SCRIPTA METALLURGICA, 1988, 22 (07): : 1005 - 1010
  • [48] HETEROGENEOUS PRECIPITATION OF INTERMEDIATE PHASES ON AL3ZR PARTICLES IN AL-CU-ZR AND AL-LI-CU-ZR ALLOYS
    KANNO, M
    OU, BL
    MATERIALS TRANSACTIONS JIM, 1991, 32 (05): : 445 - 450
  • [49] Heterogeneous precipitation of intermediate phases on Al3Zr particles in Al-Cu-Zr and Al-Li-Cu-Zr alloys
    Kanno, Motohiro, 1600, (32):
  • [50] Aging behavior of Li containing Al-Zn-Mg-Cu alloys
    Wei, BC
    Chen, CQ
    Huang, Z
    Zhang, YG
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2000, 280 (01): : 161 - 167
12345