Analysis of the Process and Results of High-Pressure Abrasive Water Jet Multilayer Cutting of Electrical Steel

被引:5
|
作者
Szada-Borzyszkowska, Monika [1 ]
Kacalak, Wojciech [1 ]
Bohdal, Lukasz [1 ]
Szada-Borzyszkowski, Wieslaw [1 ]
机构
[1] Koszalin Univ Technol, Dept Mech Engn, Racławicka 15-17 St, PL-75620 Koszalin, Poland
关键词
high-pressure abrasive water jet cutting; electrical steel; cut surface; electrical steel single layers; bundle cutting; magnetic properties; OPTIMIZATION; PARAMETERS; BLANKING;
D O I
10.3390/ma17010094
中图分类号
O64 [物理化学(理论化学)、化学物理学];
学科分类号
070304 ; 081704 ;
摘要
Electrical steels are magnetically soft materials and are widely used in the electrical industry for the construction of power transformer cores, distribution transformers, current transformers, and voltage transformers. An important parameter of electrical components, which determines the efficiency of devices, is energy loss during remagnetization. Energy losses are caused by eddy currents, hysteresis, and magnetic delay associated with the low quality of the cut edge after the cutting of steels, and material deformations and excessive stress concentration in the surrounding cutting zones. Common techniques for cutting electrical materials in industrial lines include mechanical cutting and laser cutting. Work has shown that mechanical cutting of electrical steel single layers results in the occurrence of large deformation zones, and in cutting processes with a high-pressure abrasive water jet (AWJ), significant uplifts of material and burrs at the bottom edges of sheets occur. The problem of increasing the cutting quality was solved through selecting the stream parameters for bundle cutting of electrical steels. It has been shown that in the process of cutting electrical sheet bundles, the height of burrs on the cut surface and the zone of plastic deformation are reduced. The work also presents comparison and analysis of characteristic features of the cut edge of electrical sheets obtained through high-pressure abrasive water jet and mechanical cutting processes. The influence of the type and processing parameters on the characteristic features of the material hysteresis loop was determined.
引用
收藏
页数:17
相关论文
共 50 条
  • [21] EXPERIMENTAL RESULTS FOR MATERIALS CUTTING WITH ABRASIVE WATER JET
    Daniel, Jucan
    Lucica, Anghelescu
    Mihai, Cruceru
    Cristinel, Popescu
    GEOCONFERENCE ON SCIENCE AND TECHNOLOGIES IN GEOLOGY, EXPLORATION AND MINING, SGEM 2014, VOL III, 2014, : 261 - 268
  • [22] Morselment and cutting with high-pressure water-cutting-jet for gastrointestinal endoscopy
    Heller, T
    Benz, S
    Orlowski, M
    Pein, A
    Liebe, S
    Lohr, M
    GASTROINTESTINAL ENDOSCOPY, 1997, 45 (04) : 29 - 29
  • [24] APPLICATION OF HIGH-PRESSURE WATER JET IN MINING PROCESS
    PUCHALA, RJ
    TRUXA, L
    CIM BULLETIN, 1987, 80 (902): : 102 - 102
  • [26] SIMULATION ANALYSIS OF STRIATION PHENOMENA IN ABRASIVE WATER JET CUTTING (AWJC) PROCESS OF AISI 304 STAINLESS STEEL
    Chen, X. C.
    Deng, S. S.
    Chen, M.
    Hua, W. X.
    Liao, S.
    Yao, S.
    METALURGIJA, 2018, 57 (1-2): : 114 - 116
  • [27] ANALYSIS AND MODELING OF THE EFFECTS OF PROCESS PARAMETERS ON SPECIFIC CUTTING ENERGY IN ABRASIVE WATER JET CUTTING
    Jankovic, Predrag Lj.
    Madic, Milos J.
    Petkovic, Dusan Lj.
    Radovanovic, Miroslav R.
    THERMAL SCIENCE, 2018, 22 : S1459 - S1470
  • [28] Process control for high pressure water jet cutting systems
    Kischkat, R
    13TH INTERNATIONAL CONFERENCE ON JETTING TECHNOLOGY, 1996, (21): : 595 - 611
  • [29] A Novel Technique for Spatial Objects Shaping with a High-Pressure Abrasive Water Jet
    Borkowski, Przemyslaw
    STROJNISKI VESTNIK-JOURNAL OF MECHANICAL ENGINEERING, 2010, 56 (05): : 287 - 294
  • [30] EVALUATION OF EROSION PERFORMANCE OF ABRASIVE PARTICLES IN ABRASIVE WATER JET CUTTING PROCESS
    Hlavacek, Petr
    Sitek, Libor
    Foldyna, Josef
    MM SCIENCE JOURNAL, 2020, 2020 : 3869 - 3872