Investigation of the Tribological Behaviour of Various AMC Surfaces against Brake Lining Material

被引:3
|
作者
Hirsch, Sarah Johanna [1 ]
Eiselt, Patrick [2 ]
Ozdemir, Ismail [1 ]
Grund, Thomas [1 ]
Nestler, Andreas [2 ]
Lampke, Thomas [1 ]
Schubert, Andreas [2 ]
机构
[1] Tech Univ Chemnitz, Inst Mat Sci & Engn, Mat & Surface Engn Grp, Erfenschlager Str 73, D-09125 Chemnitz, Germany
[2] Tech Univ Chemnitz, Inst Machine Tools & Prod Proc, Professorship Micromfg Technol, Reichenhainer Str 70, D-09126 Chemnitz, Germany
关键词
aluminium matrix composites; brake disc; facing; friction; surface engineering; tribology; wear; ALUMINUM-MATRIX COMPOSITES; WEAR BEHAVIOR; SLIDING WEAR; ROTOR;
D O I
10.3390/ma16031001
中图分类号
O64 [物理化学(理论化学)、化学物理学];
学科分类号
070304 ; 081704 ;
摘要
AlSi7Mg/SiCp aluminium matrix composites (AMCs) with a high ceramic content (35 vol.%) that were produced by using the field-assisted sintering technique (FAST) were subjected to tribological preconditioning and evaluated as a potential lightweight material to substitute grey cast iron brake discs. However, since an uncontrolled running-in process of the AMC surface can lead to severe wear and thus to failure of the friction system, AMC surfaces cannot be used directly after finishing and have to be preconditioned. A defined generation of a tribologically conditioned surface (tribosurface) is necessary, as was the aim in this study. To simulate tribological conditions in automotive brake systems, the prepared AMC samples were tested in a pin-on-disc configuration against conventional brake lining material under dry sliding conditions. The influence of the surface topography generated by face turning using different indexable inserts and feeds or an additional plasma electrolytic treatment was investigated at varied test pressures and sliding distances. The results showed that the coefficient of friction remained nearly constant when the set pressure was reached, whereas the initial topography of the samples studied by SEM varied substantially. A novel approach based on analysing the material ratio determined by 3D surface measurement was developed in order to obtain quantitative findings for industrial application.
引用
收藏
页数:18
相关论文
共 26 条
  • [21] Tribological behaviour of skin equivalents and ex-vivo human skin against the material components of artificial turf in sliding contact
    Hurtado, M. Morales
    Peppelman, M.
    Zeng, X.
    van Erp, P. E. J.
    Van der Heide, E.
    TRIBOLOGY INTERNATIONAL, 2016, 102 : 103 - 113
  • [22] Investigation on the Tribological Behavior of Tool-sided Tailored Surfaces for Controlling the Material Flow in Sheet-Bulk Metal Forming
    Henneberg, J.
    Lucas, H.
    Denkena, B.
    Merklein, M.
    PROCEEDINGS OF THE 22ND INTERNATIONAL ESAFORM CONFERENCE ON MATERIAL FORMING (ESAFORM 2019), 2019, 2113
  • [23] Tribological investigation of a compressor liner-ring material under various bio-based lubricants using HFRR tribometer
    Reddy, P. Chenga
    Arumugam, S.
    Krishna, P. Nithin Sai
    Sainath, N. Jaya
    3RD INTERNATIONAL CONFERENCE ON MATERIALS AND MANUFACTURING ENGINEERING 2018, 2018, 390
  • [24] Tribological investigation of ultra-high molecular weight polyethylene against advanced ceramic surfaces in total hip joint replacement
    Choudhury, Dipankar
    Roy, Taposh
    Krupka, Ivan
    Hartl, Martin
    Mootanah, Rajshree
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART J-JOURNAL OF ENGINEERING TRIBOLOGY, 2015, 229 (04) : 410 - 419
  • [25] Water's behaviour on Ca-rich tricalcium silicate surfaces for various degrees of hydration: A molecular dynamics investigation
    Claverie, Jerome
    Bernard, Fabrice
    Marques Cordeiro, Joao Manuel
    Kamali-Bernard, Siham
    JOURNAL OF PHYSICS AND CHEMISTRY OF SOLIDS, 2019, 132 : 48 - 55
  • [26] Friction, wear and material transfer of sintered polyimides sliding against various steel and diamond-like carbon coated surfaces
    Samyn, P
    Schoukens, G
    Quintelier, J
    De Baets, P
    TRIBOLOGY INTERNATIONAL, 2006, 39 (06) : 575 - 589