Effects of Particle Size Distribution of Standard Sands on the Physical-Mechanical Properties of Mortars

被引:4
|
作者
Ferreira, Ruan L. S. [1 ]
Medeiros, Mauriceia [2 ]
Pereira, Jessyca E. S. [2 ]
Henriques, Glauco F. F. [3 ]
Tavares, Jennef C. C. [4 ]
Marvila, Markssuel T. T. [5 ]
de Azevedo, Afonso R. G. [6 ]
机构
[1] Fed Inst Educ Sci & Technol Pernambuco, Civil Construct Dept, BR-55200000 Pesqueira, Brazil
[2] Univ Fed Rio Grande do Norte, Chem Engn Dept, BR-59078970 Natal, Brazil
[3] Univ Fed Paraiba, Grad Program Civil & Environm Engn PPGECAM, Campus 1 Lot Cidade Univ, BR-58051900 Joao Pessoa, Paraiba, Brazil
[4] Fed Rural Univ Semiarid, Sci & Technol Dept, BR-59780000 Caraubas, Brazil
[5] Univ Fed Vicosa, Campus Rio Paranaiba, BR-38810000 Rio Paranaiba, Brazil
[6] UENF State Univ Northern Rio de Janeiro, LECIV Civil Engn Lab, Campos Goytacazes, BR-28013602 Rio De Janeiro, Brazil
关键词
cementitious materials; particle size; granular skeleton; fine aggregate; CEMENT; MICROSTRUCTURE; AGGREGATE; BEHAVIOR; CONSTRUCTION; WASTE;
D O I
10.3390/ma16020844
中图分类号
O64 [物理化学(理论化学)、化学物理学];
学科分类号
070304 ; 081704 ;
摘要
Obtained natural sands can present different particle size distributions (PSD), although they have the same mineralogical origin. These differences directly influence the physical and mechanical behavior of mortars and, therefore, the performance of mortar and ceramic renderings. Standardizing the particle size of sands based on pre-established requirements in normative standards (NBR 7214 or ASTM C778) is one way to minimize these effects. However, these standards do not consider the optimization of the granular skeleton through the analysis of bulk density and PSD, which may be insufficient to obtain satisfactory results. Therefore, this paper analyzes the effects of using different particle size ranges on the physical and mechanical behavior of cement and hydrated lime mortars. The properties of consistency index, bulk density, air content, capillary water absorption, water absorption by immersion, flexural strength, compressive strength, and dynamic modulus of elasticity were evaluated. For this purpose, standardized sands of the same mineralogical origin were made with different particle size ranges, being: (i) standardized sand constituted by 25% of coarse and fine fractions (S25-control), (ii) standardized sand constituted by 30% of coarse fraction and 20% of fine fraction (S30-20), and (iii) standardized sand composed by 40% of coarse fraction, and 10% of fine fraction (S40-10), respectively. The results indicated that variations in the particle size composition of the standardized sands are necessary to obtain mixtures with higher compactness and, therefore, mortars with better physical and mechanical performance. Thus, the dosage of the particle size fractions of standardized sand should consider the optimization of the granular skeleton, being the unit mass and the granulometric composition as important parameters to meet this premise.
引用
收藏
页数:16
相关论文
共 50 条
  • [41] Effects of particle number and size distribution on macroscopic mechanical properties of rock models in DEM
    Shimizu H.
    Murata S.
    Ishida T.
    Zairyo/Journal of the Society of Materials Science, Japan, 2010, 59 (03) : 219 - 226
  • [42] The Effects of Quartz Content, Particle Size and Distribution Mode on the Mechanical Properties and Fracturing of Shale
    Ye, Yapei
    Tang, Shuheng
    Xi, Zhaodong
    Lu, Renqi
    Zhang, Zhongyao
    Li, Jintao
    NATURAL RESOURCES RESEARCH, 2024, 33 (01) : 239 - 262
  • [43] PHYSICAL-MECHANICAL PROPERTIES OF FODDER FOR CATTLE-BREEDING AND ITS EFFECTS ON CONVEYORS
    NEUMANN, H
    AGRARTECHNIK, 1981, 31 (10): : 463 - 466
  • [44] The Effects of Quartz Content, Particle Size and Distribution Mode on the Mechanical Properties and Fracturing of Shale
    Yapei Ye
    Shuheng Tang
    Zhaodong Xi
    Renqi Lu
    Zhongyao Zhang
    Jintao Li
    Natural Resources Research, 2024, 33 : 239 - 262
  • [45] Physical-Mechanical and Electrical Resistivity Properties of Cementitious Mortars Containing Fe3O4-MWCNTs Nanocomposite
    Selen, Veyis
    Guler, Omer
    Nodehi, Mehrab
    Sari, Ahmet
    Yaras, Ali
    Gencel, Osman
    Gholampour, Aliakbar
    Ozbakkaloglu, Togay
    SUSTAINABILITY, 2023, 15 (14)
  • [46] Physical and mechanical properties of mortars without cement
    Binici, Hanifi
    Gemci, Remzi
    Kaplan, Hasan
    CONSTRUCTION AND BUILDING MATERIALS, 2012, 28 (01) : 357 - 361
  • [47] Physical-Mechanical Properties of Stone Masonry of Gjirokaster, Albania
    Mustafaraj, Enea
    Luga, Erion
    Corradi, Marco
    Borri, Antonio
    Muceku, Ylber
    Zharkalli, Aleksandra
    MATERIALS, 2021, 14 (05) : 1 - 21
  • [48] PHYSICAL-MECHANICAL PROPERTIES OF A MEXICAN GUADUA (Guadua aculeata)
    Zaragoza-Hernandez, Idalia
    Ruben Ordonez-Candelaria, Victor
    Martha Barcenas-Pazos, Guadalupe
    Maxima Borja-de la Rosa, Amparo
    Jose Zamudio-Sanchez, Francisco
    MADERAS-CIENCIA Y TECNOLOGIA, 2015, 17 (03): : 505 - 516
  • [49] INFLUENCE OF MINERAL ADDITIONS ON THE PHYSICAL-MECHANICAL PROPERTIES OF CONCRETES
    Cuibus, Alexandrina
    Kiss, Zoltan
    Gorea, Maria
    REVISTA ROMANA DE MATERIALE-ROMANIAN JOURNAL OF MATERIALS, 2014, 44 (03): : 225 - 235
  • [50] Electrochemical metallization of abrasive materials and their physical-mechanical properties
    Malyshev, VV
    MATERIALS SCIENCE, 1997, 33 (06) : 766 - 769