Effects of Particle Size Distribution of Standard Sands on the Physical-Mechanical Properties of Mortars

被引:4
|
作者
Ferreira, Ruan L. S. [1 ]
Medeiros, Mauriceia [2 ]
Pereira, Jessyca E. S. [2 ]
Henriques, Glauco F. F. [3 ]
Tavares, Jennef C. C. [4 ]
Marvila, Markssuel T. T. [5 ]
de Azevedo, Afonso R. G. [6 ]
机构
[1] Fed Inst Educ Sci & Technol Pernambuco, Civil Construct Dept, BR-55200000 Pesqueira, Brazil
[2] Univ Fed Rio Grande do Norte, Chem Engn Dept, BR-59078970 Natal, Brazil
[3] Univ Fed Paraiba, Grad Program Civil & Environm Engn PPGECAM, Campus 1 Lot Cidade Univ, BR-58051900 Joao Pessoa, Paraiba, Brazil
[4] Fed Rural Univ Semiarid, Sci & Technol Dept, BR-59780000 Caraubas, Brazil
[5] Univ Fed Vicosa, Campus Rio Paranaiba, BR-38810000 Rio Paranaiba, Brazil
[6] UENF State Univ Northern Rio de Janeiro, LECIV Civil Engn Lab, Campos Goytacazes, BR-28013602 Rio De Janeiro, Brazil
关键词
cementitious materials; particle size; granular skeleton; fine aggregate; CEMENT; MICROSTRUCTURE; AGGREGATE; BEHAVIOR; CONSTRUCTION; WASTE;
D O I
10.3390/ma16020844
中图分类号
O64 [物理化学(理论化学)、化学物理学];
学科分类号
070304 ; 081704 ;
摘要
Obtained natural sands can present different particle size distributions (PSD), although they have the same mineralogical origin. These differences directly influence the physical and mechanical behavior of mortars and, therefore, the performance of mortar and ceramic renderings. Standardizing the particle size of sands based on pre-established requirements in normative standards (NBR 7214 or ASTM C778) is one way to minimize these effects. However, these standards do not consider the optimization of the granular skeleton through the analysis of bulk density and PSD, which may be insufficient to obtain satisfactory results. Therefore, this paper analyzes the effects of using different particle size ranges on the physical and mechanical behavior of cement and hydrated lime mortars. The properties of consistency index, bulk density, air content, capillary water absorption, water absorption by immersion, flexural strength, compressive strength, and dynamic modulus of elasticity were evaluated. For this purpose, standardized sands of the same mineralogical origin were made with different particle size ranges, being: (i) standardized sand constituted by 25% of coarse and fine fractions (S25-control), (ii) standardized sand constituted by 30% of coarse fraction and 20% of fine fraction (S30-20), and (iii) standardized sand composed by 40% of coarse fraction, and 10% of fine fraction (S40-10), respectively. The results indicated that variations in the particle size composition of the standardized sands are necessary to obtain mixtures with higher compactness and, therefore, mortars with better physical and mechanical performance. Thus, the dosage of the particle size fractions of standardized sand should consider the optimization of the granular skeleton, being the unit mass and the granulometric composition as important parameters to meet this premise.
引用
收藏
页数:16
相关论文
共 50 条
  • [1] Research on representation of particle size distribution for standard sands
    Wang, Jing
    Ling, Jinghua
    Ling, Daosheng
    Hu, Tiantian
    He, Chunjian
    POWDER TECHNOLOGY, 2023, 424
  • [2] Physical-mechanical properties of mortars with addition of TiO2 nanoparticles
    Pozo-Antonio, J. S.
    Dionisio, A.
    CONSTRUCTION AND BUILDING MATERIALS, 2017, 148 : 261 - 272
  • [3] Analysis of the physical-mechanical properties of coating mortars with the incorporation of polypropylene and nylon fibers
    Colombo, Felipe Sachet
    Pavei Antunes, Elaine Guglielmi
    Jaramillo, Leidy Johana
    Piva, Jorge Henrique
    Wanderlind, Augusto
    MATERIA-RIO DE JANEIRO, 2020, 25 (04): : 1 - 15
  • [4] Physical-mechanical properties and microstructure changes in mortars with chemically treated coir fibers
    Schiavon, Jessica Zamboni
    Borges, Pietra Moraes
    Andrade, Jairo Jose de Oliveira
    JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T, 2024, 30 : 4030 - 4043
  • [5] INFLUENCE OF PHYSICAL-MECHANICAL PROPERTIES OF FERTILIZER ON UNIFORMITY OF DISTRIBUTION
    Gavrilovic, Marija
    Dimitrijevic, Aleksandra
    Mileusnic, Zoran
    Miodragovic, Rajko
    ACTUAL TASKS ON AGRICULTURAL ENGINEERING, 2013, 41 : 164 - 170
  • [6] Physical and permeability properties of cementitious mortars having fly ash with optimized particle size distribution
    Sevim, Ozer
    Demir, Ilhami
    CEMENT & CONCRETE COMPOSITES, 2019, 96 : 266 - 273
  • [7] Investigation of Physical-Mechanical Properties and Microstructure of Mortars with Perlite and Thermal-Treated Materials
    Saca, Nastasia
    Radu, Lidia
    Stoleriu, Stefania
    Dobre, Daniela
    Calota, Razvan
    Trusca, Roxana
    MATERIALS, 2024, 17 (14)
  • [8] Effects of particle size and size distribution on the mechanical properties of EPDM/silica vulcanizates
    Ichazo, M. N.
    Albano, C.
    Hernandez, M.
    Gonzalez, J.
    Carta, A.
    MULTI-FUNCTIONAL MATERIALS AND STRUCTURES, PTS 1 AND 2, 2008, 47-50 : 113 - +
  • [9] Impact of various sands and fibres on the physical and mechanical properties of earth mortars for plasters and renders
    Pedergnana, Matthieu
    Elias-Ozkan, Soofia Tahira
    CONSTRUCTION AND BUILDING MATERIALS, 2021, 308
  • [10] PHYSICAL-MECHANICAL ANALYSIS OF ASPHALT MORTARS MADE FROM RECYCLED MATERIALS
    Ullauri, Aquiles
    Friend, Nella
    Barzola, Julio
    REVISTA UNIVERSIDAD Y SOCIEDAD, 2018, 10 (01): : 248 - 257