Effects of process parameters on the microstructure and mechanical properties of AISI 1045 steel prepared by selective laser melting

被引：6
|
作者：
Li, Yunzhe [1 ]
Liu, Shifeng [1 ]
Wang, Yan [1 ]
Wei, Yingkang [1 ]
Han, Lixiong [1 ]
Zhi, Hao [1 ]
Yang, Xin [2 ]
机构：
[1] Xian Univ Architecture & Technol, Sch Met Engn, Xian 710055, Peoples R China
[2] Xian Univ Technol, Coll Mat Sci & Engn, Xian 710048, Peoples R China
来源：
MATERIALS TODAY COMMUNICATIONS | 2023年 / 37卷
基金：
中国博士后科学基金; 中国国家自然科学基金;
关键词：
AISI; 1045; steel; Selective laser melting; Relative density; Microstructure; Strength; HEAT-TREATMENT; HIGH-STRENGTH; IMPACT;
D O I：
10.1016/j.mtcomm.2023.107287
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
AISI 1045 steel is medium carbon low alloy steel, characterized by low cost and high comprehensive properties, and it is one of the most widely used steel materials. In this study, AISI 1045 steel was successfully prepared by selective laser melting (SLM) with optimized process parameters. The influence of powder layer thickness, scanning speed, and volume energy density (VED) on the relative density, microstructure, and mechanical properties of AISI 1045 steel has been systematically investigated. The results show that the phase composition of powder and SLMed-AISI 1045 steel is mainly alpha-Fe, the microstructure of sample is mainly fine martensite, and the grain size is mainly in the range of 0.3-1.7 mu m. The sample prepared by SLM has a crystal orientation of < 101 > direction. At the same time, twin martensite and nano-precipitate were found. The Vickers hardness and compressive strength of AISI 1045 steel prepared by SLM are 541 +/- 9 HV0.1 and 2055.85 MPa, respectively. The excellent mechanical properties are mainly attributed to fine grain strengthening and precipitation strength-ening. Finally, the tensile properties and friction resistance of commercial AISI 1045 steel were measured and compared with SLMed-AISI 1045 steel. The results show that SLMed-AISI 1045 steel has high strength and wear resistance, the yield strength is 3.6 times that of commercial AISI 1045 steel, while maintaining high ductility.
引用
收藏
页数：13
相关论文
共 50 条
  • [41] Microstructure and mechanical properties of TiN particles strengthened 316L steel prepared by laser melting deposition process
    Wang, Ye
    Liu, Zhenghao
    Zhou, Yuzhao
    Yang, Xiaoshan
    Tang, Jingang
    Liu, Xue
    Li, Jinfeng
    Le, Guomin
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2021, 814
  • [42] Selective laser melting of titanium alloys: Effect of processing parameters on microstructure and mechanical properties
    Kushwaha A.
    Kumar S.A.
    Velu R.
    International Journal of Mechatronics and Manufacturing Systems, 2021, 14 (02) : 128 - 142
  • [43] Influence mechanism of parameters process and mechanical properties evolution mechanism of maraging steel 300 by selective laser melting
    Bai, Yuchao
    Yang, Yongqiang
    Wang, Di
    Zhang, Mingkang
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2017, 703 : 116 - 123
  • [44] Relationship between microstructure and mechanical properties of friction stir processed AISI 316L steel produced by selective laser melting
    Peng, Pai
    Wang, Kuaishe
    Wang, Wen
    Han, Peng
    Zhang, Ting
    Liu, Qiang
    Zhang, Shengyi
    Wang, Hongduo
    Qiao, Ke
    Liu, Jian
    MATERIALS CHARACTERIZATION, 2020, 163
  • [45] INFLUENCE OF SELECTIVE LASER MELTING PROCESS PARAMETERS ON THE MICROSTRUCTURE FORMATION
    Latypova, M. A.
    Kuzmin, S. L.
    Yerzhanov, A. S.
    USPEKHI FIZIKI METALLOV-PROGRESS IN PHYSICS OF METALS, 2023, 24 (03): : 530 - 560
  • [46] Selective laser melting of stainless steel and alumina composite: Experimental and simulation studies on processing parameters, microstructure and mechanical properties
    Li, Xinwei
    Willy, Habimana Jean
    Chang, Shuai
    Lu, Wanheng
    Herng, Tun Seng
    Ding, Jun
    MATERIALS & DESIGN, 2018, 145 : 1 - 10
  • [47] Effects of Heat Treatment on the Microstructure and Mechanical Properties of Selective Laser Melting 316L Stainless Steel
    Lei, Jingfa
    Ge, Yongsheng
    Liu, Tao
    Wei, Zhan
    SHOCK AND VIBRATION, 2021, 2021
  • [48] Microstructure and Mechanical Properties of Objects Prepared by Selective Laser Melting of AKD12 Powder
    A. S. Fefelov
    A. G. Merkushev
    O. A. Chikova
    A. B. Finkel’shtein
    Metallurgist, 2018, 62 : 470 - 475
  • [49] Microstructure and Mechanical Properties of Objects Prepared by Selective Laser Melting of AKD12 Powder
    Fefelov, A. S.
    Merkushev, A. G.
    Chikova, O. A.
    Finkel'shtein, A. B.
    METALLURGIST, 2018, 62 (5-6) : 470 - 475
  • [50] Microstructure and Mechanical Properties of Carbides Reinforced Nickel Matrix Alloy Prepared by Selective Laser Melting
    Xia, Tian
    Wang, Rui
    Bi, Zhongnan
    Wang, Rui
    Zhang, Peng
    Sun, Guangbao
    Zhang, Ji
    MATERIALS, 2021, 14 (17)
12345