Numerical Simulation of Injection Molding of three-Dimensional Thin Parts

被引：0
|
作者：
YING Daoning WANG Erjian CHENG Wenxing LU Bin
机构：
来源：
CADDM | 1991年 / 01期
关键词：
Numerical Simulation; Injection Molding;
D O I：
暂无
中图分类号：
学科分类号：
摘要：
This paper is concerned with the numerical simulation of the injection mold filling process.A mathematical model based on generalized Hele-Shaw flow for an inelastic non-Newtonian fluid undernonisothermal conditions is used.A hybrid numerical scheme is employed.The numerical simulating re-sults,pressure and temperature profile,location of the melt fronts,are in a good agreement with the ex-perimental ones.
引用
收藏
页码：29 / 34
页数：6
相关论文
共 50 条
  • [1] Three-dimensional numerical simulation of segregation in powder injection molding
    Ilinca, F.
    Hetu, J. -F.
    [J]. INTERNATIONAL POLYMER PROCESSING, 2008, 23 (02) : 208 - 215
  • [2] Numerical Filling Simulation of Injection Molding Using Three-Dimensional Model
    Geng Tie Li Dequn Zhou Huamin State Key Lab.of Mould & Die Technology
    [J]. CADDM, 2003, (Z1) : 6 - 14
  • [3] Three-dimensional numerical simulation for plastic injection-compression molding
    Yun Zhang
    Wenjie Yu
    Junjie Liang
    Jianlin Lang
    Dequn Li
    [J]. Frontiers of Mechanical Engineering, 2018, 13 : 74 - 84
  • [4] Three-dimensional numerical simulation for plastic injection-compression molding
    Zhang, Yun
    Yu, Wenjie
    Liang, Junjie
    Lang, Jianlin
    Li, Dequn
    [J]. FRONTIERS OF MECHANICAL ENGINEERING, 2018, 13 (01) : 74 - 84
  • [5] Three-dimensional simulation of plastic injection molding
    Talwar, K
    Costa, F
    Rajupalem, V
    Antanovski, L
    Friedl, C
    [J]. CONFERENCE PROCEEDINGS AT ANTEC '98: PLASTICS ON MY MIND, VOLS I-3: VOL I; PROCESSING, VOL II; SPECIAL AREAS, VOL III; MATERIALS, 1998, 44 : 562 - 566
  • [6] Three-dimensional simulation of the injection molding process
    Rajupalem, V
    Talwar, K
    Friedl, C
    [J]. ANTEC'97 - PLASTICS SAVING PLANET EARTH, CONFERENCE PROCEEDINGS, VOLS 1 - 3, 1997, : 670 - 673
  • [7] Parallel three-dimensional simulation of the injection molding process
    Araujo, B. J.
    Teixeira, J. C. F.
    Cunha, A. M.
    Groth, C. P. T.
    [J]. INTERNATIONAL JOURNAL FOR NUMERICAL METHODS IN FLUIDS, 2009, 59 (07) : 801 - 815
  • [8] Three-dimensional simulation of the rubber injection molding process
    Capellmann, R
    Haberstroh, E
    [J]. ANTEC 2000: SOCIETY OF PLASTICS ENGINEERS TECHNICAL PAPERS, CONFERENCE PROCEEDINGS, VOLS I-III, 2000, : 461 - 466
  • [9] Three-dimensional numerical modeling of co-injection molding
    Ilinca, F
    Hétu, JF
    [J]. INTERNATIONAL POLYMER PROCESSING, 2002, 17 (03) : 265 - 270
  • [10] Numerical simulation of three-dimensional fiber orientation in injection molding including fountain flow effect
    Han, KH
    Im, YT
    [J]. POLYMER COMPOSITES, 2002, 23 (02) : 222 - 238
12345