Simulation of Adaptive Control Strategy for Electrical Discharge Machining Process

被引：0
|
作者：
杨青照 [1 ]
周明 [1 ]
田洪森 [1 ]
张惠生 [1 ]
许东晖 [1 ]
机构：
[1] School of Mechanical-Electronic and Automobile Engineering, Beijing University of Civil Engineering and Architecture
来源：
Journal of Shanghai Jiaotong University(Science) | 2015年 / 20卷 / 04期
基金：
北京市自然科学基金;
关键词：
electrical discharge machining(EDM); adaptive control; electrode down-time; Matlab simulation;
D O I：
暂无
中图分类号：
TG661 [电加工机床及其加工];
学科分类号：
080201 ;
摘要：
Electrode down-time is an important factor affecting the efficiency and stability of electrical discharge machining(EDM) process. In the research, a way of simulating the regulation of the electrode down-time in an EDM adaptive control system has been studied. All the simulations are performed on Matlab. The simulation results demonstrate that this adaptive controller by regulating electrode down-time can direct the gap state to follow the specified reference gap state with or without disturbances. Finally, the adaptive control scheme is also validated by experiments. The significance of the simulation of an EDM adaptive control system lies on the fact that it provides a convenient way to guide the actual production and provides a new study method for the research of EDM control strategy with no regard of experimental conditions.
引用
收藏
页码：408 / 414
页数：7
相关论文
共 50 条
  • [1] Simulation of adaptive control strategy for electrical discharge machining process
    Yang Q.-Z.
    Zhou M.
    Tian H.-S.
    Zhang H.-S.
    Xu D.-H.
    [J]. Journal of Shanghai Jiaotong University (Science), 2015, 20 (04) : 408 - 414
  • [2] Analysis and Control of Electrical Discharge Machining (EDM) Process
    Zhou, Ming
    Han, Fuzhu
    Meng, Xianyi
    Chen, Baojiang
    [J]. 2009 IEEE INTERNATIONAL CONFERENCE ON INDUSTRIAL ENGINEERING AND ENGINEERING MANAGEMENT, VOLS 1-4, 2009, : 164 - 168
  • [3] ADAPTIVE CONTROL SYSTEM OF THE ELECTRIC DISCHARGE MACHINING PROCESS
    Erenkov, O. Yu.
    Sarilov, M. Yu.
    [J]. CHEMICAL AND PETROLEUM ENGINEERING, 2016, 52 (3-4) : 182 - 186
  • [4] Simulation of electrical discharge machining
    Kunieda M.
    [J]. Seimitsu Kogaku Kaishi/Journal of the Japan Society for Precision Engineering, 2010, 76 (08): : 861 - 866
  • [5] On Adaptive Control for Electrical Discharge Machining Using Vibroacoustic Emission
    Melnik, Yury A.
    Kozochkin, Mikhail P.
    Porvatov, Artur N.
    Okunkova, Anna A.
    [J]. TECHNOLOGIES, 2018, 6 (04):
  • [6] Control Strategy for Electrical Discharge Machining (EDM) Pulse Power Generator
    Ade Erawan, Minhat
    Nor Hisham, Khamis
    Azli, Yahya
    Trias, Andromeda
    Kartiko, Nugroho
    Nor Liyana Safura, Hashim
    Nazriah, Mahmud
    Razak, M.
    [J]. MECHANICAL AND MATERIALS ENGINEERING, 2014, 554 : 643 - +
  • [7] Electrical discharge machining of ceramic nanocomposites: sublimation phenomena and adaptive control
    Grigoriev, Sergey N.
    Kozochkin, Mikhail P.
    Porvatov, Artur N.
    Volosova, Marina A.
    Okunkova, Anna A.
    [J]. HELIYON, 2019, 5 (10)
  • [8] Modeling and simulation of electrical discharge machining
    Weingaertner, E.
    Kuster, F.
    Wegener, K.
    [J]. 1ST CIRP GLOBAL WEB CONFERENCE: INTERDISCIPLINARY RESEARCH IN PRODUCTION ENGINEERING (CIRPE2012), 2012, 2 : 74 - 78
  • [9] High efficient electrical discharge machining by servo voltage adaptive control
    Mu, Xin
    Zhou, Ming
    Yao, Shengzuo
    Yang, Jianwei
    [J]. 19TH CIRP CONFERENCE ON ELECTRO PHYSICAL AND CHEMICAL MACHINING, 2018, 68 : 654 - 659
  • [10] Machining process of insulating ceramics by electrical discharge machining
    Tani, Takayuki
    Fukuzawa, Yasushi
    Furutani, Katsushi
    Mohri, Naotake
    [J]. Seimitsu Kogaku Kaishi/Journal of the Japan Society for Precision Engineering, 1997, 63 (09): : 1310 - 1314
12345