Model for Local Cavitation Instabilities in Two-Bladed Turbopump Inducers

被引:0
|
作者
Yoon, Youngkuk [1 ]
Song, Seung Jin [1 ]
机构
[1] Seoul Natl Univ, 1 Gwanak ro, Seoul 08826, South Korea
来源
关键词
turbopump inducer; local cavitation instabilities; centrifugal compressors and pumps;
D O I
10.1115/1.4067027
中图分类号
TH [机械、仪表工业];
学科分类号
0802 ;
摘要
Various local cavitation instabilities in turbopump inducers (e.g., alternate blade cavitation, supersynchronous rotating cavitation) have been previously experimentally identified. However, a model that is capable of predicting such local instabilities is still lacking. Therefore, a new model, which models an N-bladed inducer as a system of N-coupled mass-spring-damper systems, is presented to predict postonset behavior of alternate blade cavitation instabilities. The model predicts that alternate blade cavitation will occur. As the flow coefficient is decreased, the model predicts that the magnitude of alternate blade cavitation first increases and then decreases and then finally vanishes. If the flow coefficient is further decreased beyond the range of alternate blade cavitation, a sudden increase in equilibrium incidence is predicted. All of these predictions agree with the previous experimental findings. Furthermore, simultaneous in-phase oscillations of the blade cavities are predicted during alternate blade cavitation. These in-phase oscillations of the cavities correspond to the surge mode oscillation, which had been previously mistakenly categorized as a global (system) instability. Finally, it is proposed that the aforementioned postonset behaviors of alternate blade cavitation are general in two-bladed inducers, as long as the change in incidence on the following blade has a local minimum when it is expressed as a function of leading blade's incidence.
引用
收藏
页数:10
相关论文
共 50 条
  • [21] Modal dynamics of structures with bladed isotropic rotors and its complexity for two-bladed rotors
    Hansen, Morten Hartvig
    WIND ENERGY SCIENCE, 2016, 1 (02) : 271 - 296
  • [22] DYNAMIC MODEL BASED IDENTIFICATION OF CAVITATION COMPLIANCE AND MASS FLOW GAIN FACTOR IN ROCKET ENGINE TURBOPUMP INDUCERS
    Wan, Y.
    Manfredi, M.
    Pasini, A.
    Spakovszky, Z.
    PROCEEDINGS OF THE ASME TURBO EXPO 2020: TURBOMACHINERY TECHNICAL CONFERENCE AND EXPOSITION, VOL 2E, PT II, 2020,
  • [23] Geometry Effects on Flow Instabilities of Different Three-Bladed Inducers
    Pace, Giovanni
    Valentini, Dario
    Pasini, Angelo
    Torre, Lucio
    Fu, Yanxia
    d'Agostino, Luca
    JOURNAL OF FLUIDS ENGINEERING-TRANSACTIONS OF THE ASME, 2015, 137 (04):
  • [24] Design of a two-bladed 10 MW rotor with teetering hub
    Civati, M.
    Sartori, L.
    Croce, A.
    SCIENCE OF MAKING TORQUE FROM WIND (TORQUE 2018), 2018, 1037
  • [25] Integrated yaw design of a downwind two-bladed wind turbine
    van Solingen, Edwin
    van Wingerden, Jan-Willem
    Beerens, Jan
    2015 AMERICAN CONTROL CONFERENCE (ACC), 2015, : 3702 - 3707
  • [27] STUDYING THE DRAG OF A TWO-BLADED WIND TURBINE IN THE OPERATING MODE
    Kussaiynov, K.
    Tanasheva, N. K.
    Turgunov, M. M.
    Dyusembaeva, A. N.
    Alibekova, A.
    VESTNIK TOMSKOGO GOSUDARSTVENNOGO UNIVERSITETA-MATEMATIKA I MEKHANIKA-TOMSK STATE UNIVERSITY JOURNAL OF MATHEMATICS AND MECHANICS, 2014, (30): : 82 - 87
  • [28] Iterative tuning of feedforward IPC for two-bladed wind turbines
    Mulders, S. P.
    van Solingen, E.
    van Wingerden, J. W.
    Beerens, J.
    SCIENCE OF MAKING TORQUE FROM WIND (TORQUE 2016), 2016, 753
  • [29] CFD COMPUTATION, ANALYSIS AND DESIGN OF A TWO-BLADED WASTEWATER PUMP
    Litfin, Oliver
    Mohr, Christian
    Haddad, Kais
    Epple, Philipp
    Semel, Matthias
    Becker, Klaus
    Klein, Horst
    Delgado, Antonio
    PROCEEDINGS OF THE ASME INTERNATIONAL MECHANICAL ENGINEERING CONGRESS AND EXPOSITION, 2011, VOL 6, PTS A AND B, 2012, : 919 - 926
  • [30] DOWNWIND TWO-BLADED WIND TURBINE AERODYNAMIC PERFORMANCE EVALUATION IMPLEMENTING ACTUATOR LINE MODEL
    Henao, Sebastian
    Benavides, Aldo G.
    Lopez, Omar D.
    PROCEEDINGS OF THE ASME INTERNATIONAL MECHANICAL ENGINEERING CONGRESS AND EXPOSITION, 2018, VOL 7, 2019,