EXPERIMENTAL STUDY ON CHANNEL-CASING REINFORCED SHS X-JOINTS UNDER IN-PLANE BENDING

被引：0

作者：

Chang H.-F. ^{[1
,2
]}

Li Z.-W. ^{[1
,2
]}

Zuo W.-K. ^{[1
,3
]}

Luo Z. ^{[4
]}

An A.-C. ^{[1
]}

Song X.-Y. ^{[1
]}

机构：

[1] Jiangsu Key Laboratory of Environmental Impact and Structural Safety in Engineering, China University of Mining & Technology, Jiangsu, Xuzhou

[2] JiangSu Collaborative Innovation Center for Building Energy Saving and Construction Technology, Jiangsu Vocational Institute of Architectural Technology, Jiangsu, Xuzhou

[3] School of Naval Architecture, Ocean & Civil Engineering, Shanghai Jiao Tong University, Shanghai

[4] Service Center of General Aviation Industry in Caidian, Hubei, Wuhan

来源：

Gongcheng Lixue/Engineering Mechanics | 2024年 / 41卷 / 05期

关键词：

bearing mechanism; channel-casing reinforcement; in-plane bending; SHS; X-joints;

D O I：

10.6052/j.issn.1000-4750.2022.05.0407

中图分类号：

学科分类号：

摘要：

Channel-casing can effectively improve the capacity and stiffness of joints, which can be used for local reinforcement of steel tubular joint in service. To study the in-plane bending performance of channel-casing reinforced SHS (square hollow section) joint, 5 SHS X-joints with a brace-to-chord diameter ratio β of 0.58, 0.7 and 1.0 were tested under in-plane bending load. The results show that the channel-casing reinforcement can effectively improve the bending performance of joints. When β=0.58 and β=0.7, the bending capacity of channel-casing reinforced joints increases by 37% and 163% respectively. The stiffness of reinforced joints is slightly lower than that of the joint with equal width, but its ductility is better. The brace-to-chord diameter ratio and the thickness of the channel-casing are two key parameters influencing the in-plane bending behavior of the reinforced joints. And the reinforcement of channel-casing can effectively protect the chord of the joint, which leads to the transformation of failure mode of specimens from the failure of chord or welding seam to the failure of brace. Further mechanism analysis shows that the channel-casing can form a common bearing carrier with a chord wall, which improves the bearing capacity and stiffness of the joint owing to local thickening. Finally, the applicability of the formulas for calculating the flexural capacity of the channel-casing reinforced joints are compared and analyzed, and suggestions for design are proposed. © 2024 Tsinghua University. All rights reserved.

引用

页码：96 / 106

页数：10

共 32 条

[21] CHEN K M, HUANG H H, WU Q X, Et al., Experimental and finite element analysis research on the fatigue performance of CHS K-joints, Engineering Structures, 197, (2019)
[22] CHANG Hongfei, Bearing mechanism and mechanical model of reinforced SHS joint and truss structure, (2013)
[23] CHEN Yu, ZHANG Zuanhu, Experimental study of in-plane bending property of concrete filled brace circular section X-joints, China Civil Engineering Journal, 45, 7, pp. 97-104, (2012)
[24] GB/T 2975−2018, Steel and steel products-Location and preparation of samples and test pieces for mechanical testing, (2018)
[25] GB/T 228.1−2010, Metallic materials-Tensile testing-Part 1: Method of test at room temperature, (2011)
[26] CHEN Yiyi, PENG Li, Experimental study on bending properties of through-type rectangular tubular joint, Journal of Building Structures, 25, 3, pp. 1-7, (2004)
[27] ZHAO X L., Deformation limit and ultimate strength of welded T-joints in cold-formed RHS sections [J], Journal of Constructional Steel Research, 53, 2, pp. 149-165, (2000)
[28] CHEN Y, CHEN D F., Ultimate capacities formulae of collar and doubler plates reinforced SHS X-joints under in-plane bending [J], Thin-Walled Structures, 99, pp. 21-34, (2016)
[29] CHANG Hongfei, LI Zhaowei, QIAN Yulong, Et al., Experimental and parametric study on flexural performance of transverse reverse channel connections between square hollow section column and H-beam, Journal of Building Structures, 42, 2, pp. 92-102, (2021)
[30] CHEN Yiyi, ZHAO Bida, WANG Wei, Et al., Behavior of unstiffened CHS KK-joints under cyclic out-of-plane bending, China Civil Engineering Journal, 43, 11, pp. 8-16, (2010)

← 1 2 3 4 →