EXPERIMENTAL STUDY ON CHANNEL-CASING REINFORCED SHS X-JOINTS UNDER IN-PLANE BENDING

被引：0
|
作者：
Chang H.-F. [1 ,2 ]
Li Z.-W. [1 ,2 ]
Zuo W.-K. [1 ,3 ]
Luo Z. [4 ]
An A.-C. [1 ]
Song X.-Y. [1 ]
机构：
[1] Jiangsu Key Laboratory of Environmental Impact and Structural Safety in Engineering, China University of Mining & Technology, Jiangsu, Xuzhou
[2] JiangSu Collaborative Innovation Center for Building Energy Saving and Construction Technology, Jiangsu Vocational Institute of Architectural Technology, Jiangsu, Xuzhou
[3] School of Naval Architecture, Ocean & Civil Engineering, Shanghai Jiao Tong University, Shanghai
[4] Service Center of General Aviation Industry in Caidian, Hubei, Wuhan
来源：
Gongcheng Lixue/Engineering Mechanics | 2024年 / 41卷 / 05期
关键词：
bearing mechanism; channel-casing reinforcement; in-plane bending; SHS; X-joints;
D O I：
10.6052/j.issn.1000-4750.2022.05.0407
中图分类号：
学科分类号：
摘要：
Channel-casing can effectively improve the capacity and stiffness of joints, which can be used for local reinforcement of steel tubular joint in service. To study the in-plane bending performance of channel-casing reinforced SHS (square hollow section) joint, 5 SHS X-joints with a brace-to-chord diameter ratio β of 0.58, 0.7 and 1.0 were tested under in-plane bending load. The results show that the channel-casing reinforcement can effectively improve the bending performance of joints. When β=0.58 and β=0.7, the bending capacity of channel-casing reinforced joints increases by 37% and 163% respectively. The stiffness of reinforced joints is slightly lower than that of the joint with equal width, but its ductility is better. The brace-to-chord diameter ratio and the thickness of the channel-casing are two key parameters influencing the in-plane bending behavior of the reinforced joints. And the reinforcement of channel-casing can effectively protect the chord of the joint, which leads to the transformation of failure mode of specimens from the failure of chord or welding seam to the failure of brace. Further mechanism analysis shows that the channel-casing can form a common bearing carrier with a chord wall, which improves the bearing capacity and stiffness of the joint owing to local thickening. Finally, the applicability of the formulas for calculating the flexural capacity of the channel-casing reinforced joints are compared and analyzed, and suggestions for design are proposed. © 2024 Tsinghua University. All rights reserved.
引用
收藏
页码：96 / 106
页数：10
相关论文
共 32 条
  • [1] ZHAO Bida, CAI Yangzheng, WANG Wei, Effect of the brace-to-chord angle on the out-of-plane flexural behavior of unstiffened CHS X-joints, Engineering Mechanics, 36, 7, pp. 99-108, (2019)
  • [2] WANG Qingfan, QU Hui, LI Wei, Et al., Study on impact performance of K-type tubular joints with stiffening inner rings, Engineering Mechanics, 39, 5, pp. 133-144, (2022)
  • [3] MA Xinxu, CHEN Yiyi, Ultimate strength formulae for RHS-CHS T-joints under axial compression, Engineering Mechanics, 34, 5, pp. 163-170, (2017)
  • [4] SHEN Guohui, CHEN Zhen, GUO Yong, Et al., Bearing capacity of cross-shaped steel tubular joints with reinforced plate under brace compression, Engineering Mechanics, 30, 9, pp. 70-75, (2013)
  • [5] AHMADI H, LOTFOLLAHI-YAGHIN M A, ASOODEH S., Degree of bending (DoB) in tubular K-joints of offshore structures subjected to in-plane bending (IPB) loads: Study of geometrical effects and parametric formulation [J], Ocean Engineering, 102, pp. 105-116, (2015)
  • [6] ZHAO Zhongwei, WU Gang, Random compression capacity of corroded WHSJS, Engineering Mechanics, 38, 5, pp. 219-228, (2021)
  • [7] CHENG B, HUANG F H, LI C, Et al., Hot spot stress and fatigue behavior of bird-beak SHS X-joints subjected to brace in-plane bending, Thin-Walled Structures, 150, (2020)
  • [8] CHANG H F, XIA J W, ZHANG F J, Et al., Compression behavior of doubler-plate reinforced square hollow section T-joints [J], Advanced Steel Construction, 10, 3, pp. 289-309, (2014)
  • [9] WANG Wenjie, SHAO Yongbo, XIA Hui, Research on the static strength of square tubular T-joints reinforced with collar plate under axial compression, Engineering Mechanics, 29, 6, pp. 138-145, (2012)
  • [10] CHANG Hongfei, XIA Junwu, DUAN Xiaomu, Et al., Experimental study on compression capacity of doubler or vertical inner plate reinforced square tubular T-joints, Journal of Building Structures, 34, 10, pp. 57-63, (2013)
1234