INJECTION MOLDING OF CR POLYPROPYLENE.

被引：0
|
作者：
Bormuth, H.
机构：
来源：
| 1600年 / 76期
关键词：
CR POLYPROPYLENE - FLOWABILITY - THIN-WALLED PARTS;
D O I：
暂无
中图分类号：
学科分类号：
摘要：
(Edited Abstract)
引用
收藏
相关论文
共 50 条
  • [21] Morphological comparison of isotactic polypropylene parts prepared by micro-injection molding and conventional injection molding
    Liu, Fanghui
    Guo, Chao
    Wu, Xian
    Qian, Xinyuan
    Liu, Hong
    Zhang, Jie
    POLYMERS FOR ADVANCED TECHNOLOGIES, 2012, 23 (03) : 686 - 694
  • [22] Injection molding of polypropylene reinforced with short jute fibers
    Karmaker, AC
    Youngquist, JA
    JOURNAL OF APPLIED POLYMER SCIENCE, 1996, 62 (08) : 1147 - 1151
  • [23] Injection Molding Shrinkage and Mechanical Properties of Polypropylene Blends
    Qi, Guo-Qiang
    Xu, Ya-Jun
    Yang, Wei
    Xie, Bang-Hu
    Yang, Ming-Bo
    JOURNAL OF MACROMOLECULAR SCIENCE PART B-PHYSICS, 2011, 50 (09): : 1747 - 1760
  • [24] Highly stereoregular syndiotactic polypropylene.
    Miller, SA
    Bercaw, JE
    ABSTRACTS OF PAPERS OF THE AMERICAN CHEMICAL SOCIETY, 1999, 217 : U989 - U989
  • [25] Reducing the injection molding temperature of polypropylene by hyperbranched polymers
    Han, KQ
    Cai, ZH
    Wu, CX
    Yu, MH
    Proceedings of 2005 International Conference on Advanced Fibers and Polymer Materials (ICAFPM 2005), Vol 1 and 2: NEW CENTURY , NEW MATERIALS AND NEW LIFE, 2005, : 29 - 30
  • [26] Optical monitoring of polypropylene crystallization during injection molding
    Favaro, Marcia M.
    Marinelli, Alessandra L.
    Farah, Marcelo
    Bretas, Rosario E. S.
    POLYMER ENGINEERING AND SCIENCE, 2008, 48 (02): : 257 - 266
  • [27] Influence of the polypropylene structure on the replication of nanostructures by injection molding
    Vera, Julie
    Brulez, Anne-Catherine
    Contraires, Elise
    Larochette, Mathieu
    Valette, Stephane
    Benayoun, Stephane
    JOURNAL OF MICROMECHANICS AND MICROENGINEERING, 2015, 25 (11)
  • [28] Aluminum/polypropylene composites produced through injection molding
    Li, Xiping
    Gong, Ningning
    Yang, Can
    Zeng, Shuiping
    Fu, Shihong
    Zhang, Ke
    JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2018, 255 : 635 - 643
  • [29] Temperature distributions of molten polypropylene during injection molding
    Sombatsompop, N
    Chaiwattanpipat, W
    ADVANCES IN POLYMER TECHNOLOGY, 2000, 19 (02) : 79 - 86
  • [30] SELF-REINFORCEMENT OF POLYPROPYLENE IN INJECTION-MOLDING
    PROX, M
    EHRENSTEIN, GW
    KUNSTSTOFFE-GERMAN PLASTICS, 1991, 81 (11): : 1057 - 1060
12345