CRACK RESISTANCE OF POLYCARBONATE AND POLYMETHYL METHACRYLATE AT HIGH LOADING RATES.

被引：0

作者：

Eremenko, A.S. ^{[1
]}

Novikov, S.A. ^{[1
]}

Sinitsyn, V.A. ^{[1
]}

Girin, A.S. ^{[1
]}

机构：

[1] State Committee on the Use of Atomic, Energy of the USSR, USSR, State Committee on the Use of Atomic Energy of the USSR, USSR

来源：

Soviet materials science | 1985年 / 21卷 / 04期

关键词：

CRACK RESISTANCE - FRACTURE TOUGHNESS;

D O I：

暂无

中图分类号：

学科分类号：

摘要：

Recently significant attention has been devoted to the application of linear fracture mechanics methods to investigation of the fracture characteristics of polymer materials, the mechanical properties of which depend significantly upon the temperature and rate conditions of loading. The temperature and rate relationships of crack resistance of polymers is investigated in this paper. A newly proposed method of high-rate crack resistance tests with the use of a split Hopkinson bar and a special axial cleavage specimen is employed. With its use the range of loading rates in investigation of specimens of polymethyl methacrylate and polycarbonate is significantly broadened to K equals 30,000 sec** minus **1. Disk specimens were tested at 20 degree C and minus 15 degree C. The crack growth rate was determined from the motion pictures. Crack growth rate depends linearly on the loading rate. The rates of crack resistance of polycarbonate is more than twice the crack resistance of polymethyl methacrylate.

引用

页码：368 / 371

共 50 条

[41] Frequency Honing for High Removal Rates.
Hunger, Walter
Werkstatt und Betrieb, 1985, 118 (07): : 393 - 395
[42] METALLURGICAL EFFECTS AT HIGH STRAIN RATES.
1973,
[43] EXAMPLES OF THE USE OF DATA ITEMS ON FATIGUE CRACK PROPAGATION RATES.
Anon
Engineering Sciences Data Unit, Data Items, 1974, (74017):
[44] Concerning the cause of high protuberance rates.
Anderson, W
ZEITSCHRIFT FUR PHYSIK, 1924, 22 : 322 - 327
[45] Test method for the determination of crack-growth rates and crack growth resistance under cyclic loading
Yarema, SY
MATERIALS SCIENCE, 1994, 30 (06) : 706 - 717
[46] Grafting of bisphenol-A polycarbonate and polymethyl methacrylate on to the surface of carbon fibers via anionic polymerization
Raghavendran, VK
Drzal, LT
COMPOSITE INTERFACES, 2002, 9 (01) : 1 - 23
[47] A novel process for separation of polycarbonate, polyvinyl chloride and polymethyl methacrylate waste plastics by froth flotation
Wang, Chong-qing
Wang, Hui
Huang, Luo-luo
WASTE MANAGEMENT, 2017, 65 : 3 - 10
[48] THE STUDIES OF PHASE-SEPARATION AND CHEMICAL-REACTIONS IN BLENDS OF POLYCARBONATE WITH SYNDIOTACTIC POLYMETHYL METHACRYLATE
KO, CC
KYU, T
ABSTRACTS OF PAPERS OF THE AMERICAN CHEMICAL SOCIETY, 1993, 206 : 305 - POLY
[49] GRAFT COPOLYMER OF POLYMETHYL METHACRYLATE-G-POLYCARBONATE URETHANE AND THE FULLY GELLED GRAFTED NETWORKS
ZHOU, PG
FRISCH, HL
JOURNAL OF POLYMER SCIENCE PART A-POLYMER CHEMISTRY, 1992, 30 (12) : 2577 - 2585
[50] High-strain-rate properties of polymethyl methacrylate
Sato, Y
Kikuchi, W
IMPACT ENGINEERING AND APPLICATION, VOLS I AND II, 2001, : 833 - 838

← 1 2 3 4 5 →