Effects of punch load for elliptical deep drawing product of automotive parts

被引：0
|
作者：
School of Mechanical, Manufacturing and Medical Engineering, Queensland University of Technology, Gardens Point Campus, 2 George Street, Brisbane, QLD 4001, Australia [1 ]
机构：
来源：
International Journal of Advanced Manufacturing Technology | 2008年 / 35卷 / 7-8期
关键词：
Deep drawing process; one of sheet metal forming methods; is very useful in industrial field because of its efficiency. The production of optimal products using this process is dependent on the process variables such as blank shapes; profile radii of punch and die; and formability of materials. Of the variables; the blank shape is very important since it controls the formability factor. This paper reports the investigations on three kinds of blank shapes and the scribed circle test on three deformation modes. The punch load distribution for elliptical forming processes were measured under different conditions of profile radii of punch and die and discussed here. These experiments clarified the influence of the profile radii of the punch and die and the blank shape on the punch-load distribution for the elliptical deep drawing product of automobile parts. The aim of this study is to investigate the effect that the process variables have on drawability in a non-axisymmetric elliptical deep-drawing process and to obtain useful data from the industrial field. © 2006 Springer-Verlag London Limited;
D O I：
暂无
中图分类号：
学科分类号：
摘要：
Journal article (JA)
引用
收藏
页码：814 / 820
相关论文
共 50 条
  • [21] A study on the improvement of formability for elliptical deep drawing processes
    Park, DH
    Kang, SS
    Park, SB
    JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2001, 113 (1-3) : 662 - 665
  • [22] THE EFFECT OF DIE/PUNCH RADIUS AND DRAWING RATIO ON THE WALL THICKNESS IN DEEP DRAWING DIES
    Ozek, Cebeli
    Bal, Muhammet
    JOURNAL OF THE FACULTY OF ENGINEERING AND ARCHITECTURE OF GAZI UNIVERSITY, 2009, 24 (01): : 33 - 41
  • [23] Effects of Variable Punch Speed and Blank Holder Force in Warm Superplastic Deep Drawing Process
    Manabe, Ken-ichi
    Soeda, Kentaro
    Shibata, Akinori
    METALS, 2021, 11 (03) : 1 - 16
  • [24] A CAPP system for axisymmetrical deep drawing parts
    Abbassi, Fethi
    Ben Yahia, Nouredine
    Zghal, Ali
    INTERNATIONAL JOURNAL OF AUTOMATION AND CONTROL, 2007, 1 (2-3) : 118 - 132
  • [25] THE PREDICTION OF FAILURE ON DEEP DRAWING OF RECTANGULAR PARTS
    DOEGE, E
    STRACKERJAHN, W
    STAHL UND EISEN, 1982, 102 (18): : 895 - 898
  • [26] COLD-SHAPED PARTS - DEEP DRAWING
    不详
    MACHINE DESIGN, 1974, 46 (04) : 149 - 150
  • [27] Hemispherical parts Numerical simulation of deep drawing
    Su Bingling
    FRONTIERS OF MANUFACTURING AND DESIGN SCIENCE IV, PTS 1-5, 2014, 496-500 : 769 - 772
  • [28] The analysis of the parameters for deep drawing of cylindrical parts
    Chiorescu, Dan
    Chiorescu, Esmeralda
    Olaru, Sergiu
    22ND INTERNATIONAL CONFERENCE ON INNOVATIVE MANUFACTURING ENGINEERING AND ENERGY - IMANE&E 2018, 2018, 178
  • [29] A fuzzy logic model to determine the effects of die/blank holder angle and punch radius on drawing ratio in angular deep drawing dies
    Ozek, Cebeli
    Celik, Yahya Hisman
    Ozek, Muzeyyen Bulut
    JOURNAL OF INTELLIGENT & FUZZY SYSTEMS, 2013, 25 (02) : 379 - 388
  • [30] Numerical analysis of wrinkling phenomenon in hydroforming deep drawing with hemispherical punch
    Ziaeipoor, H.
    Jamshidifard, S.
    Moosavi, H.
    Khademizadeh, H.
    SELECTED TOPICS IN SYSTEM SCIENCE AND SIMULATION IN ENGINEERING, 2010, : 96 - +
12345