The possibility of friction stir welding of high nitrogen-containing austenitic stainless steel

被引:0
|
作者
Miyano Y. [1 ]
Fujii H. [2 ]
Sun Y. [2 ]
Ieko K. [3 ]
Katada Y. [4 ]
Kamiya O. [3 ]
机构
[1] Faculty of Educational Systems and Studies, Akita University, Akita-city, AKITA, 1-1, Tegatagakuen-Machi
[2] Joining and Welding Research Institute, Osaka University, Suita, Osaka 565-0871
[3] Faulty of Engineering and Resource Science, Akita University, Akita-city, AKITA, 1-1, Tegatagakuen-Machi
[4] National Institute for Materials Science, Tsukuba-city Ibaraki 305-0047
关键词
α; formation; Austenite; Butt-welding; Electro-slag remelting methods; Friction stir welding;
D O I
10.5188/ijsmer.17.197
中图分类号
学科分类号
摘要
To develop the practical use of high nitrogen-containing austenitic stainless steels (HNS), the possibility of using friction stir welding (FSW) of HNS was examined. In this report, butt-welding of 2 mm thick HNS steel plates was performed using a load-controlled FSW machine. Two types of welding tool materials were used in this study, namely, a Si3N4-based material and a WC-Co-based material. For FSW with Si3N4, fullpenetrated and defect-free butt welding joints were successfully produced. On the other hand, for FSW with WC-Co, the tool was deformed and the stir zone did not completely reach the bottom. The stir zone produced by the Si3N4 tool showed a Vicker's hardness higher than the base metal and displayed a fine microstructure due to recrystallization. The yield strength and the tensile strength of the welds produced by the Si3N4 tool exceeded that of the base metal. © 2010 Soc. Mater. Eng. Resour.
引用
收藏
页码:197 / 200
页数:3
相关论文
共 50 条
  • [31] Dissimilar Friction Stir Welding of Austenitic and Duplex Stainless Steel: Effect of Material Position and Tool Offset
    Wang, Wenyang
    Wang, Zhaoxin
    Xu, Lixia
    Hu, Ye
    Zhao, Hongwei
    STEEL RESEARCH INTERNATIONAL, 2020, 91 (10)
  • [32] Grain Structure Development During Friction Stir Welding of Single-Crystal Austenitic Stainless Steel
    Jong Jin Jeon
    Sergey Mironov
    Yutaka S. Sato
    Hiroyuki Kokawa
    Seung Hwan C. Park
    Satoshi Hirano
    Metallurgical and Materials Transactions A, 2013, 44 : 3157 - 3166
  • [33] Effects of laser welding on the microstructure evolution and corrosion resistance of a novel nitrogen-containing austenitic stainless steel QN2109
    Wang, Xiangyu
    He, Pei
    Zhou, Qingyuan
    Kong, Qingmao
    Zheng, Chun
    Sun, Yangting
    Li, Jin
    Jiang, Laizhu
    Jiang, Yiming
    JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T, 2023, 24 : 303 - 317
  • [34] Microstructure, mechanical and corrosion properties of friction stir welded high nitrogen nickel-free austenitic stainless steel
    Li, H. B.
    Jiang, Z. H.
    Feng, H.
    Zhang, S. C.
    Li, L.
    Han, P. D.
    Misra, R. D. K.
    Li, J. Z.
    MATERIALS & DESIGN, 2015, 84 : 291 - 299
  • [35] Thermodynamic study on welding wire design of high nitrogen austenitic stainless steel
    明珠
    王克鸿
    屈天鹏
    王伟
    冯胜强
    China Welding, 2019, 28 (01) : 49 - 55
  • [36] Structural response of superaustenitic stainless steel to friction stir welding
    Mironov, S.
    Sato, Y. S.
    Kokawa, H.
    Inoue, H.
    Tsuge, S.
    ACTA MATERIALIA, 2011, 59 (14) : 5472 - 5481
  • [37] Effects of interlayer on the friction stir spot welding of stainless steel
    Raza, Muhammad Farhan
    Yapici, Guney Guven
    MATERIALS TODAY-PROCEEDINGS, 2022, 62 : 4291 - 4294
  • [38] TEXTURE EVOLUTION DURING FRICTION STIR WELDING OF STAINLESS STEEL
    Cho, Jaehyung
    MATERIALS PROCESSING AND TEXTURE, 2009, 200 : 3 - 16
  • [39] Metallurgical and mechanical properties of high nitrogen austenitic stainless steel friction welds
    Woo, I
    Aritoshi, M
    Kikuchi, Y
    ISIJ INTERNATIONAL, 2002, 42 (04) : 401 - 406
  • [40] Effect of Welding Parameters on Properties of Friction Stir Welded High Nitrogen Steel
    Sato, Yutaka S.
    Nakamura, Kei
    Kokawa, Hiroyuki
    TRENDS IN WELDING RESEARCH: PROCEEDINGS OF THE 9TH INTERNATIONAL CONFERENCE, 2013, : 280 - 283