Misfiring characteristics during cold-start in an EFI LPG engine

被引:0
|
作者
Liu, Zhi-Min [1 ]
Li, Li-Guang [2 ]
Gong, Chang-Ming [3 ]
Li, Gong [1 ]
Zhai, Hong-Bin [1 ]
Deng, Bao-Qing [3 ]
机构
[1] Key Laboratory for Power Machinery and Engineering, Shanghai Jiaotong University, Shanghai 200030, China
[2] School of Automotive Studies, Tongji University, Shanghai 201804, China
[3] Department of Internal Combustion Engine, Jilin University, Changchun 130025, China
关键词
Electric control equipment - Fuel injection - Gas emissions - Ignition - Liquefied petroleum gas - Starting;
D O I
暂无
中图分类号
学科分类号
摘要
Experiments were conducted in a 125 cm3 single cylinder EFI SI engine fuelled with LPG. The complete misfiring of designed cycles was created by absence spark ignition. The effect of different cycles during cold-start on start-up speed and HC emissions with single-cycle misfiring, continuous two-cycle and three-cycle misfiring was studied. The HC emissions at different misfiring ratio during the first 120 cycles from cold-start were compared. The key cycle affecting cold-start speed and HC emissions were found experimentally, i.e. the ideal first firing cycle and the next cycle. Misfiring of the ideal first firing cycle has a strong effect on HC and start-up speed in cold start. Misfiring in the next cycle after the ideal first firing cycle affects the HC emissions secondarily. Misfiring of the other cycles have similar effect on HC emissions. Heightening the start-up speed was helpful for the stability of idle running. HC emissions are in a certain proportion to misfiring ratio. With one time increase of misfiring ratio, HC emissions increased by one time approximately. When the misfiring ratio was higher than 5%, the total HC emissions increased rapidly.
引用
收藏
页码:545 / 550
相关论文
共 50 条
  • [31] COLD-START CHARACTERISTICS OF POLYMER ELECTROLYTE FUEL CELLS: A SIMPLFIED ANALYSIS
    Wang, Yun
    Mishler, Jeff
    Mukherjee, Partha P.
    Mukundan, Rangachary
    Borup, Rodney L.
    PROCEEDINGS OF THE ASME INTERNATIONAL HEAT TRANSFER CONFERENCE - 2010, VOL 5: FUEL CELLS, GAS TURBINES, HEAT PIPES, JET IMPINGEMENT, RADIATION, 2010, : 97 - 102
  • [32] Spray Characteristics of Standard and Alternative Aviation Fuels at Cold-start Conditions
    Shin, Dongyun
    Rodrigues, Neil S.
    Bokhart, Andrew J.
    Sojka, Paul E.
    Gore, Jay P.
    Lucht, Robert P.
    AIAA JOURNAL, 2021, 59 (12) : 5238 - 5250
  • [33] Modelling three-way catalytic converter oriented to engine cold-start conditions
    Real, Marcelo
    Hedinger, Raffael
    Pla, Benjamin
    Onder, Christopher
    INTERNATIONAL JOURNAL OF ENGINE RESEARCH, 2021, 22 (02) : 640 - 651
  • [34] Internal combustion engine cold-start efficiency: A review of the problem, causes and potential solutions
    Roberts, Andrew
    Brooks, Richard
    Shipway, Philip
    ENERGY CONVERSION AND MANAGEMENT, 2014, 82 : 327 - 350
  • [35] Cold-start emissions of an SI engine using ethanol-gasoline blended fuel
    Chen, Rong-Horng
    Chiang, Li-Bin
    Chen, Chung-Nan
    Lin, Ta-Hui
    APPLIED THERMAL ENGINEERING, 2011, 31 (8-9) : 1463 - 1467
  • [36] COMPUTATION OF COLD-START MISS RATIOS
    EASTON, MC
    IEEE TRANSACTIONS ON COMPUTERS, 1978, 27 (05) : 404 - 408
  • [37] Variational cold-start resistant recommendation
    Walker, Joojo
    Zhang, Fengli
    Zhong, Ting
    Zhou, Fan
    Baagyere, Edward Yellakuor
    INFORMATION SCIENCES, 2022, 605 : 267 - 285
  • [38] Electronically Controlling the System of Preheating Intake Air by Flame for Diesel Engine Cold-Start
    杜巍
    赵福堂
    Journal of Beijing Institute of Technology, 2003, (02) : 158 - 161
  • [39] Computational Investigations of Spray Atomization and Evaporation Under Cold-Start Conditions of a Diesel Engine
    Sonawane, Utkarsha
    Agarwal, Avinash Kumar
    JOURNAL OF ENERGY RESOURCES TECHNOLOGY-TRANSACTIONS OF THE ASME, 2022, 144 (11):
  • [40] COLD-START CFD SIMULATION OF SPARK-IGNITION DIRECT-INJECTION ENGINE
    Yang, Xiaofeng
    Kuo, Tang-Wei
    Singh, Kulwinder
    Hattar, Rafat
    Zeng, Yangbing
    PROCEEDINGS OF THE ASME INTERNAL COMBUSTION ENGINE FALL TECHNICAL CONFERENCE, 2017, VOL 2, 2017,