Studying the influence of process parameters on the catalytic carbon nanofibers formation using factorial design

被引：0

作者：

Jarrah, Nabeel A. ^{[1
]}

机构：

[1] Department of Chemical Engineering, Mutah University, P.O. Box 7, 61710 Karak, Jordan

来源：

Chemical Engineering Journal | 2009年 / 151卷 / 1-3期

关键词：

Carbon nanofibers were catalytically grown by the decomposition of C2H2/H2 over an unsupported Ni catalyst. The aim of this article is to study the main and interaction effects of temperature (500-600 °C); H2 flow rate (0-100 ml/min); and C2H2 flow rate (100-200 ml/min) on the yield and properties of carbon nanofibers. Full 23 factorial designs with three replicates at the center point and thus a total of 11 experiments were carried out. It turns out that when temperature increases there was a significant increase in the yield; in the BET; and also in the pore volume of the carbon nanofibers. On the other hand; increasing H2 flow rate decreases the yield; the BET; and also decreases the pore volume of carbon nanofibers. Increasing C2H2 flow rate has an insignificant effect on the yield and it decreases the BET surface area and pore volume. The work shows that not only the effects of the main parameters are important; but also the interaction effects between them are significant. The study helps optimizing the process of carbon nanofibers growth. © 2009 Elsevier B.V. All rights reserved;

D O I：

暂无

中图分类号：

学科分类号：

摘要：

Journal article (JA)

引用

页码：367 / 371

共 50 条

[41] Fluid catalytic cracking optimisation using factorial design and genetic algorithm techniques
Cuadros, Jose F.
Melo, Delba C.
Maciel Filho, Rubens
Wolf Maciel, Maria R.
CANADIAN JOURNAL OF CHEMICAL ENGINEERING, 2013, 91 (02): : 279 - 290
[42] INFLUENCE OF PROCESS VARIABLES ON ADSORPTION OF CONGO RED ONTO MANGO LEAF CHAR USING FACTORIAL DESIGN ANALYSIS
Gunasekar, Varadarajan
Ramadoss, Govindarajan
Ponnusami, Venkatachalam
ENVIRONMENTAL ENGINEERING AND MANAGEMENT JOURNAL, 2017, 16 (12): : 2745 - 2753
[43] Modeling and Analysis of the Effect of Dip-Spin Coating Process Parameters on Coating Thickness Using Factorial Design Method
Buapool, Sorasutee
Thavarungkul, Nandh
Srisukhumbowornchai, Nakorn
Termsuksawad, Preecha
ADVANCES IN MATERIALS SCIENCE AND ENGINEERING, 2017, 2017
[44] Study of the influence of some factors on the preparation of activated carbon from walnut cake using the fractional factorial design
El Maguana, Y.
Elhadiri, N.
Bouchdoug, M.
Benchanaa, M.
JOURNAL OF ENVIRONMENTAL CHEMICAL ENGINEERING, 2018, 6 (01): : 1093 - 1099
[45] Evidence of Ternary Inclusion Complexes Formation Using Factorial Design and Determination of Their Formation Constant
Gabriela Roa-Morales
Laura Galicia
M. T. Ramírez-Silva
Journal of inclusion phenomena and macrocyclic chemistry, 2003, 46 : 139 - 145
[46] The influence of preparation parameters on the mass production of vapor-grown carbon nanofibers
Fan, YY
Cheng, HM
Wei, YL
Su, G
Shen, ZH
CARBON, 2000, 38 (06) : 789 - 795
[47] The influence of MWCVD process parameters on formation of SIC.
Dul, K
Jonas, S
ANNALES DE CHIMIE-SCIENCE DES MATERIAUX, 2003, 28 : S125 - S132
[48] Evidence of ternary inclusion complexes formation using factorial design and determination of their formation constant
Roa-Morales, G
Galicia, L
Ramírez-Silva, MT
JOURNAL OF INCLUSION PHENOMENA AND MACROCYCLIC CHEMISTRY, 2003, 46 (3-4) : 139 - 145
[49] Influence of Process Parameters on Formation of Al/Cu Dissimilar Weld Using Ultrasonic Welding
Bum-Su Go
Kyoung-Hak Kim
Chan-Seung Ro
Hee-Seon Bang
International Journal of Precision Engineering and Manufacturing, 2022, 23 : 1359 - 1365
[50] Influence of Process Parameters on Formation of Al/Cu Dissimilar Weld Using Ultrasonic Welding
Go, Bum-Su
Kim, Kyoung-Hak
Ro, Chan-Seung
Bang, Hee-Seon
INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING, 2022, 23 (12) : 1359 - 1365

← 1 2 3 4 5 →