INVESTIGATION INTO SLM BLADE INCLINATION EFFECT ON POWDER SPREADING BEHAVIOR BASED ON DISCRETE ELEMENT METHOD

被引：0
|
作者：
Li W. [1 ]
Liu Q. [1 ]
Gao Y. [1 ]
Chu X. [2 ]
Zhang Z. [3 ]
Wang Z. [1 ]
机构：
[1] Jiangxi Key Laboratory of Forming and Joining Technology for Aerospace Components, Nanchang Hangkong University, Nanchang
[2] School of Civil Engineering, Wuhan University, Wuhan
[3] Department of Engineering Mechanics, Dalian University of Technology, Liaoning, Dalian
来源：
Lixue Xuebao/Chinese Journal of Theoretical and Applied Mechanics | / 56卷 / 03期
关键词：
blade inclination; discrete element method; flow mechanism; selective laser melting; spreading process;
D O I：
10.6052/0459-1879-23-462
中图分类号：
学科分类号：
摘要：
The blade inclination plays a significant role on the powder spreading behavior during the selective laser melting process. In this paper, a discrete element numerical model is established to investigate the powder spreading process and quality with different blade inclination angles. A quantitative indicator was proposed for different blade inclination angles to comprehensively evaluate the packing density and uniformity of the powder layer and the influence law of blade inclination on deposition quality is obtained. Based on the particle distribution and motion characteristics, the particle heap is divided into four zones including bottom layer zone, slope zone, blade influence zone, and internal zone. The powder spreading dynamic mechanism is comprehensively analyzed for the four regions, including particle trajectories and velocity fields, the shear band in front of the blade, and the distribution and evolution of inter-particle forces. It is found that when the inclination angle is less than zero, it is difficult for the particle heap to form a complete circulating flow, the shear band is relatively small, fewer particles flow towards the deposition layer, the packing density of powder layer decreases, fewer strong force chains between particles form, and force arches are easily formed in front of the blade gap, leading to particle jamming and the formation of voids. Therefore, the density and uniformity of deposition layer are poor. When the angle is greater than zero, the circulating movement of particle system is adequate, the shear band is larger, and more particles flow to the deposition layer, and the packing density of powder layer increases. As the inclination angle increases, the strong force chains increase, and the compaction effect of the blade is enhanced, which is beneficial for improving the density and uniformity of the deposition layer. This study provides a theoretical reference for the process parameter optimization and powder bed quality improvement. © 2024 Chinese Society of Theoretical and Applied Mechanics. All rights reserved.
引用
收藏
页码：774 / 784
页数：10
相关论文
共 32 条
  • [11] Nan W, Ghadiri M., Numerical simulation of powder flow during spreading in additive manufacturing, Powder Technology, 342, pp. 801-807, (2019)
  • [12] Xiang ZW, Zhang MD, Yan R, Et al., Powder-spreading dynamics and packing quality improvement for laser powder bed fusion additive manufacturing, Powder Technology, 389, pp. 278-291, (2021)
  • [13] Feng Yiqi, Xie Guoyin, Zhang Bi, Et al., Influence of laser power and surface condition on balling behavior in selective laser melting, Acta Aeronauticaet Astronautica Sinica, 40, 12, pp. 234-243, (2019)
  • [14] Sun Yuanyuan, Jiang Wugui, Xu Gaogui, Et al., Influence of rough surface of deposited area on quality of powder spreading during selective laser melting: Discrete element simulations, Chinese Journal of Theoretical and Applied Mechanics, 53, 12, pp. 3217-3227, (2021)
  • [15] Zhang J, Tan Y, Xiao X, Et al., Comparison of roller-spreading and blade-spreading processes in powder-bed additive manufacturing by DEM simulations, Particuology, 66, pp. 48-58, (2022)
  • [16] Chen Hui, Yan Wentao, Dynamic behavio-urs of powder particles in selective laser melting additive manufacturing, Chinese Journal of Theoretical and Applied Mechanics, 53, 12, pp. 3206-3216, (2021)
  • [17] Wang L, Yu A, Li E, Et al., Effects of spreader geometry on pow-der spreading process in powder bed additive manufacturing, Powder Technology, 384, pp. 211-222, (2021)
  • [18] Wu S, Lei Z, Jiang M, Et al., Experimental investigation and discrete element modeling for particle-scale powder spreading dynamics in powder-bed-fusion-based additive manufacturing, Powder Technology, 403, (2022)
  • [19] Cheng T, Chen H, Teng Q, Et al., In-situ experiment tests and particulate simulations on powder paving process of additive manufacturing, Particuology, 74, pp. 164-172, (2023)
  • [20] Yao D, An X, Fu H, Et al., Dynamic investigation on the powder spreading during selective laser melting additive manufacturing, Additive Manufacturing, 37, (2021)
1234