Progressive trends of die casting - Vacuum treatment of casting mold

被引：1
|
作者：
PaŠko J. [1 ]
GaŠpár Š. [1 ]
机构：
[1] Technical University of Kosice, Faculty of Manufacturing Technologies, Bayerova 1, Presov
来源：
| 1600年 / Trans Tech Publications Ltd卷 / 669期
关键词：
Die casting; Porosity of castings; Vacuuming the mold;
D O I：
10.4028/www.scientific.net/KEM.669.103
中图分类号：
学科分类号：
摘要：
In these days in foundry branch there is a rapid development of sectors of special casting technology with the aim to increase the quality and the efficiency of pressure casting production. Internal homogeneity of pressure casting, characterized by the extent of porosity can be affected by the setup of technological parameters of pressure casting and last but not least by vacuuming the molds, that means to exhaust air and gases from the mold cavity. Contribution is specifically aimed on the analyzing the impact of degassing pressure molds on the porosity of pressure casting from EN AC43400 Alloy. © 2016 Trans Tech Publications, Switzerland.
引用
收藏
页码：103 / 109
页数：6
相关论文
共 50 条
  • [21] INFLUENCE OF CASTING MOLD SIZE ON THE TITANIUM CASTING
    KUROIWA, A
    IGARASHI, Y
    JOURNAL OF DENTAL RESEARCH, 1995, 74 : 241 - 241
  • [22] Mold filling in casting by vacuum suction with the use of polystyrene pattern
    Churkin, B.S.
    Gofman, E.B.
    Karpov, V.V.
    Gorshkov, A.A.
    Litejnoe Proizvodstvo, 2002, (06): : 31 - 33
  • [23] Effect of Vacuum on Die Filling in High Pressure Die Casting: Water Analog, Process Simulation and Casting Validation
    Nicole Trometer
    Larry A. Godlewski
    Eben Prabhu
    Marcus Schopen
    Alan A. Luo
    International Journal of Metalcasting, 2024, 18 : 69 - 85
  • [24] EFFECT OF VACUUM ON DIE FILLING IN HIGH PRESSURE DIE CASTING: WATER ANALOG, PROCESS SIMULATION AND CASTING VALIDATION
    Trometer, Nicole
    Godlewski, Larry A.
    Prabhu, Eben
    Schopen, Marcus
    Luo, Alan A.
    INTERNATIONAL JOURNAL OF METALCASTING, 2024, 18 (01) : 69 - 85
  • [25] Mechanism of the mold collapse defect for iron casting in expendable pattern casting process with dry sand and vacuum
    Wu, Zhichao
    Huang, Naiyu
    Luo, Jirong
    2000, Chinese Mech Eng Soc, China (49):
  • [26] Mechanism of the mold collapse defect for iron casting in expendable pattern casting process with dry sand and vacuum
    2000, Chinese Mech Eng Soc, China (49):
  • [27] Die Casting Mold Design for Aluminum Alloy Shell of Instrument
    Li, Yuanyuan
    Wang, Meng
    Guo, Yuchao
    2015 7TH INTERNATIONAL CONFERENCE ON MECHANICAL AND ELECTRONICS ENGINEERING (ICMEE 2015), 2015, 31
  • [28] EVOLUTION OF MSC DIE-CASTING MOLD RELEASE AGENTS
    SMITH, RW
    DIE CASTING ENGINEER, 1990, 34 (06): : 38 - 38
  • [29] Quick casting of precision die through prototyping resin mold
    Ma, T.
    Xing, J.D.
    Fang, L.
    Wang, E.Z.
    Hsi-An Chiao Tung Ta Hsueh/Journal of Xi'an Jiaotong University, 2001, 35 (03): : 292 - 297
  • [30] LOW-MELTING BRASSES FOR PERMANENT MOLD AND DIE CASTING
    KIRBY, GN
    BADIA, FA
    COVERT, RA
    FONDERIE-FRANCE, 1967, (252): : 81 - &
12345