Analysis of the minimum injection melt on gas-assistanted injection process in 1-dimension filling model

被引：0

作者：

Li, Xiao-Ming ^{[1
]}

Chi, Jian-Feng ^{[1
]}

Li, Yi ^{[1
]}

Liu, Cheng-De ^{[1
]}

Tian, Hu ^{[1
]}

机构：

[1] Jilin University, Changchun 130025, China

来源：

Gaofenzi Cailiao Kexue Yu Gongcheng/Polymeric Materials Science and Engineering | 2007年 / 23卷 / 01期

关键词：

Filling - Gases - Mathematical models - Pressure;

D O I：

暂无

中图分类号：

学科分类号：

摘要：

Long, cylindrical parts are usually produced with Gas-Assisted Injection Molding (GAIM) which can greatly reduce the required injection pressure and the parts' weight. However, improper setting of initial injection melt will lead to insufficiency of gas penetration or gas blow out. therefore analysis of the initial injection melt is necessary. In this article, the initial injection melt in the gas-assisted injection process was studied as gas penetration taking place in 1-dimension model, the volume of gas hollowing out was equal to the same of the melt front advancing during the filling stage of the whole process, also the formula for the minimum injection melt was given finally which can give directions for practice.

引用

页码：21 / 23

共 50 条

[21] Three-dimensional simulation of melt filling and gas penetration in gas-assisted injection molding process using a finite volume formulation
Department of Mechanical Engineering, R and D Center for Membrane Technology, Chung Yuan University, Jhongli, Taiwan
不详
J Polym Eng, 2006, 5 (431-450):
[22] Three-dimensional simulation of melt filling and gas penetration in gas-assisted injection molding process using a finite volume formulation
Chau, SW
Lin, YW
JOURNAL OF POLYMER ENGINEERING, 2006, 26 (05) : 431 - 450
[23] Prediction of the mould filling process in injection moulding: Flow simulation and process analysis
Buchholz, HV
Hill, A
KAUTSCHUK GUMMI KUNSTSTOFFE, 1997, 50 (02): : 126 - 131
[24] Prediction of the mould filling process in injection moulding: flow simulation and process analysis
Buchholz, H.-V.
Bockenem, A.Hill
Kautschuk und Gummi, Kunststoffe, 1997, 50 (02): : 126 - 130
[25] Influence of Mold Temperature on Melt Filling Process of a Thin Plate Part with Microstructures in Injection Molding
Liu, Jitao
Zhao, Guoqun
Guan, Yanjin
ADVANCED SCIENCE LETTERS, 2011, 4 (8-10) : 2681 - 2685
[26] Three dimensional filling analysis of the gas-assisted injection molding
Gao, DM
ANTEC '99: PLASTICS BRIDGING THE MILLENNIA, CONFERENCE PROCEEDINGS, VOLS I-III: VOL I: PROCESSING; VOL II: MATERIALS; VOL III: SPECIAL AREAS;, 1999, : 561 - 565
[27] Three dimensional filling analysis of gas-assisted injection molding
Gao, DM
JOURNAL OF REINFORCED PLASTICS AND COMPOSITES, 2001, 20 (13) : 1090 - 1099
[28] Analysis of mold filling associated with unsteady flow in injection molding process
Lyu, MY
Shin, HC
Pae, Y
POLYMER-KOREA, 2000, 24 (04) : 545 - 555
[29] Computer simulation and analysis of fountain flow in filling process of injection molding
Li, C.S.
Hung, C.F.
Shen, Y.K.
Journal of Polymer Research, 1994, 1 (02) : 163 - 173
[30] Visualization analysis of the filling behavior of melt into microscale V-grooves during the filling stage of injection molding
Han, X.
Yokoi, H.
POLYMER ENGINEERING AND SCIENCE, 2006, 46 (11): : 1590 - 1597

← 1 2 3 4 5 →