Fault-tolerant Control of Fifteen-phase Induction Machine Under Asymmetrical Fault Condition

被引：0
|
作者：
Zheng X. [1 ]
Ma W. [2 ]
Wang D. [2 ]
Yi X. [2 ]
Liu H. [2 ]
机构：
[1] College of Electrical and Electronic Engineering, Huazhong University of Science and Technology, Wuhan, 430074, Hubei Province
[2] National Key Laboratory of Science and Technology on Vessel Integrated Power System, Naval University of Engineering, Wuhan, 430033, Hubei Province
来源：
Wang, Dong (wangdongl@sina.vip.com) | 2018年 / Chinese Society for Electrical Engineering卷 / 38期
基金：
中国国家自然科学基金;
关键词：
Asymmetrical fault condition; Fifteen-phase induction machine; Maximum torque; Tolerant-fault control;
D O I：
10.13334/j.0258-8013.pcsee.170331
中图分类号：
学科分类号：
摘要：
The superior fault-tolerant capability is one of the most significant advantages of the multi-phase induction machines. The post-fault currents with the maximum torque were optimized of a fifteen-phase induction machine under asymmetrical fault condition. The corresponding fault-tolerant control strategy was proposed. The fault-tolerant control was based on the normal decoupling transformation and machine mathematical model, thus the machine parameters need not be recalculated and the reconfiguration of the controller was minimized. Different open-circuited faults of a 45kW prototype 15-phase induction machine were analyzed and tested. The good agreement between calculated and experimental results verifies the accuracy of the proposed fault-tolerant control. © 2018 Chin. Soc. for Elec. Eng.
引用
收藏
页码：1212 / 1221
页数：9
相关论文
共 22 条
  • [1] Ma W., Wang D., Cheng S., Et al., Common basic scientific problems and development of leading-edge technology of high performance motor system, Proceedings of the CSEE, 36, 8, pp. 2025-2035, (2016)
  • [2] Ma W., Electromechanical power conversion technologies in vessel integrated power system, Journal of Electrical Engineering, 10, 4, pp. 1-10, (2015)
  • [3] Wang D., Wu X., Guo Y., Et al., Electromotive force calculation of fifteen-phase induction motors with non-sinusoidal supply, Proceedings of the CSEE, 33, 9, pp. 129-137, (2013)
  • [4] Wang D., Wu X., Cheng S., Et al., Steady state performance analysis of multi-phase induction motor with non-sinusoidal supply, Scientia Sinica: Technologica, 45, 3, pp. 322-329, (2015)
  • [5] Wang D., Wu X., Chen J., Et al., A distributed magnetic circuit approach to analysis of multiphase induction machines with nonsinusoidal supply, IEEE Trans. on Energy Conversion, 30, 2, pp. 522-532, (2015)
  • [6] Zhu P., Zhang X., Qiao M., Et al., Tolerant control strategy for five-phase concentrated full-pitch windings induction motor under open phases fault, Proceedings of the CSEE, 31, 33, pp. 131-137, (2011)
  • [7] Duran M.J., Barrero F., Recent advances in the design, modeling, and control of multiphase machines: Part II, IEEE Transactions on Industrial Electronics, 63, 1, pp. 459-468, (2016)
  • [8] Che H.S., Duran M.J., Levi E., Et al., Postfault operation of an asymmetrical six-phase induction machine with single and two isolated neutral points, IEEE Trans. on Power Electronics, 29, 10, pp. 5406-5416, (2014)
  • [9] Dwari S., Parsa L., An optimal control technique for multiphase PM machines under open-circuit faults, IEEE Trans. on Industrial Electronics, 55, 5, pp. 1988-1995, (2008)
  • [10] Kestelyn X., Semail E., A vectorial approach for generation of optimal current references for multiphase permanent-magnet synchronous machines in real time, IEEE Trans. on Industrial Electronics, 58, 11, pp. 5057-5065, (2011)
123