Abrasion Resistance Mechanism of New Co-Based Alloy by Diode Laser Cladding

被引：0
|
作者：
Wu G. [1 ,2 ]
Ren F. [1 ,2 ]
Yao J. [1 ,2 ]
Mao W. [3 ]
Li H. [3 ]
机构：
[1] Institute of Laser Advanced Manufacturing, Zhejiang University of Technology, Hangzhou, 310014, Zhejiang
[2] Zhejiang Provincial Collaborative Innovation Center of High-end Laser Manufacturing Equipment, Hangzhou, 310014, Zhejiang
[3] Bray (China) Controls System Co. Ltd, Hangzhou, 311231, Zhejiang
来源：
Yao, Jianhua (laser@zjut.edu.cn) | 1600年 / Science Press卷 / 44期
关键词：
Abrasion resistance; Co-based alloy; Laser cladding; Laser technique; Microstructure;
D O I：
10.3788/CJL201744.0602006
中图分类号：
学科分类号：
摘要：
Stellite 3, Stellite 21 and new Co-based alloy (Co-3) coatings are prepared on the 316 stainless steel surface by laser cladding. The microstructure and phase composition of the cladding layers are analysed and the microhardness distribution and abrasion resistance mechanism are also studied. The experimental results show that the microstructure of the Co-3 is homogeneous, compact, and without cracks and cavity, where the main phases consist of (Co,W)3C, Cr23C6, Cr7C3, and Co3Mo. The average microhardness of the cladding layer is about 624 HV0.2, which is more than 3 times higher than that of the substrate. The abrasion resistance performance of Co-3 is superior to that of the 316 substrate. Under the load of 0~150 N condition, when the scratching length s≤3.3 mm, the main scratch mechanism is plastic deformation; when the scratching length 3.3<s≤6.9 mm, the main scratch mechanism is grain sliding and crack formation caused by plastic deformation; when the scratching length s>6.9 mm, the main scratch mechanism is crack propagation and plastic removal. © 2017, Chinese Lasers Press. All right reserved.
引用
收藏
相关论文
共 16 条
  • [11] Alimardani M., Fallah V., Khajepour A., Et al., The effect of localized dynamic surface preheating in laser cladding of Stellite 1, Surface and Coatings Technology, 204, 23, pp. 3911-3919, (2010)
  • [12] Guo S., Dong G., Ye Z., Et al., Research on mechanical properties of a steam turbine rotor remanufactured by laser cladding, Journal of Chinese Society of Power Engineering, 34, 8, pp. 668-672, (2014)
  • [13] Kashani H., Amadeh A., Ghasemi H.M., Room and high temperature wear behaviors of nickel and cobalt base weld overlay coatings on hot forging dies, Wear, 262, 7, pp. 800-806, (2007)
  • [14] Zhang S., Huang J., Non-ferrous Metal Smelting and Casting, pp. 144-146, (2006)
  • [15] Huang P., Liu R., Wu X., Et al., Effects of molybdenum content and heat treatment on mechanical and tribological properties of a low-carbon Stellite alloy, Journal of Engineering Materials and Technology, 129, 4, pp. 523-529, (2007)
  • [16] Cui W., Chen J., Lu H., Et al., Influence of grain boundary sliding on ductility-dip cracking of Ni-based alloy, The Chinese Journal of Nonferrous metals, 5, pp. 1269-1274, (2013)
12