Adhesively bonded blanks for local reinforcements in body-in-white manufacturing

被引：0

作者：

机构：

[1] Wisner, G.

[2] Stammen, E.

[3] Dilger, K.

[4] Spiekermeier, A.

[5] Jalanesh, M.

[6] Hübner, Sven

[7] Behrens, B.-A.

来源：

Wisner, G. (g.wisner@tubraunschweig.de) | 1600年 / Bellwether Publishing, Ltd.卷 / 92期

关键词：

Adhesively bonded blanks are manufactured using a method for combined forming and bonding of locally reinforced parts for body-in-white in the automotive and truck industry. The method allows lightweight constructions with steel sheets by generally reducing the thickness of body parts and compensates stiffness as well as strength by steel grades of higher yield points and locally applied reinforcement sheets where necessary. Applying adhesive bonding in the body-in-white shops implies certain boundary conditions; such as bonding on oiled surfaces and curing at cataphoretic burn-in after coating. Adhesive bonding; with the forming process being employed between; was successfully applied with film adhesives based on different polymer families and works the best in two steps; as the formation of already bonded and cured parts causes much damage to the bond lines. Due to the early softening stage in the electro coat (EC) burn-in oven; the adhesive in most cases needs the assistance of an additional fixation technique to avoid negative results of unwanted spring-back behaviour (especially with reinforcement sheets with higher yield points). Efficient auxiliary techniques for fixation are usually not based on adhesive technology because of a process-related short time frame. Three different fixation techniques additionally to the adhesive bonding of the reinforcement sheets were investigated in a research project. This paper discusses options and results on the complex interaction between forming and adhesive bonding. © Copyright 2016 Taylor & Francis Group; LLC;

D O I：

暂无

中图分类号：

学科分类号：

摘要：

Journal article (JA)

引用

页码：7 / 9

共 50 条

[41] Unilateral and bilateral adhesively bonded joints between Fe-SMA and steel for structural reinforcements
Qiang, Xuhong
Duan, Xinran
Jiang, Xu
Zhou, Mukai
Xiao, Fei
ENGINEERING STRUCTURES, 2025, 326
[42] Thermal nondestructive testing (TNDT) of adhesively bonded composite reinforcements applied to concrete civil structures
Burleigh, D
Bohner, R
NONDESTRUCTIVE EVALUATION OF BRIDGES AND HIGHWAYS III, 1999, 3587 : 105 - 115
[43] Soft-sensing in body-in-white assembly quality control
Wang, Hua
Jiliang Xuebao/Acta Metrologica Sinica, 2006, 27 (04): : 309 - 312
[44] The effect of orientations of metal macrofiber reinforcements on mechanical properties of adhesively bonded single lap joints
Giv, A. Nemati
Ayatollahi, M. R.
Razavi, S. M. J.
Khoramishad, H.
JOURNAL OF ADHESION, 2018, 94 (07): : 541 - 561
[45] Model analysis of car's body-in-white based on FEA
Wang, Yuan
Xu, Li
Dai, Xiliang
Peng, Shenghui
PROGRESS IN POWER AND ELECTRICAL ENGINEERING, PTS 1 AND 2, 2012, 354-355 : 454 - 457
[46] Validation of Automatic Modal Parameter Estimator on a Car Body-in-White
Gioia, N.
Daems, Pieter-Jan
Helsen, J.
TOPICS IN MODAL ANALYSIS & TESTING, VOL 8, 2020, : 279 - 284
[47] Prediction of Automotive Body-in-White Distortion in Paint Baking Process
Cai, Wayne
Bondy, Matthew
Carlson, Blair
Baylis, Mark
MANUFACTURING LETTERS, 2024, 41 : 270 - 280
[48] Strength analysis of body-in-white panels accounting for the forming process
Dressler, B
Hahn, T
Sielaff, J
NUMERICAL ANALYSIS AND SIMULATION IN VEHICLE ENGINEERING, 1998, 1411 : 215 - 225
[49] Optimization of damping pad distribution on body-in-white car structure
Sipos, David
Treszkai, Marcell Ferenc
Feszty, Daniel
JOURNAL OF VIBROENGINEERING, 2022, 24 (02) : 386 - 393
[50] Development of flexible positioning system for assembly line of body-in-white
Wang, Chun
Liu, Donghai
Lin, Sheng
MANUFACTURING PROCESS AND EQUIPMENT, PTS 1-4, 2013, 694-697 : 1799 - 1802

← 1 2 3 4 5 →