High-speed wheel-rail interfacial adhesion and surface damage behavior of wheel in wide temperature range

被引：0
|
作者：
Shen M.-X. [1 ,2 ,3 ]
Qin T. [2 ]
Li S.-X. [2 ]
Peng J.-F. [3 ]
Xiong G.-Y. [2 ]
Zhu M.-H. [3 ]
机构：
[1] State Key Laboratory of Performance Monitoring and Guarantee of Rail Transportation Infrastructure, East China Jiaotong University, Nanchang
[2] School of Materials Science and Engineering, East China Jiaotong University, Nanchang
[3] State Key Laboratory of Traction Power, Southwest Jiaotong University, Chengdu
来源：
Jiaotong Yunshu Gongcheng Xuebao/Journal of Traffic and Transportation Engineering | 2021年 / 21卷 / 03期
基金：
中国国家自然科学基金;
关键词：
High-speed wheel-rail interface; Rail engineering; Seasonal damage; Wear mechanism; Wheel wear; Wide temperature range;
D O I：
10.19818/j.cnki.1671-1637.2021.03.019
中图分类号：
学科分类号：
摘要：
The wheel-rail rolling tester in a high/low temperature environment was built, and the seasonal damage characteristics of wheel surfaces with delamination and pits appearing in winter, and unusually smooth characteristics presenting in summer in the Harbin-Dalian Railway and other alpine railways, were successfully reproduced under laboratory conditions. The wheel-rail interface adhesion and wheel damage behavior of high-speed trains in a wide temperature range (-50 ℃-60 ℃) were studied. The evolution laws of the adhesion coefficient of wheel-rail rolling contact interface were systematically discussed under different service temperatures, and the important characteristics of wheel surface worn morphology and plastic behavior of surface materials were analyzed. Research results show that the adhesion coefficient of wheel-rail interface decreases with an increase of the service temperature. At the same time, the sizes of the pits on the wheel surface decrease, and the pits disappear and the worn surface becomes smoother at 60 ℃. At a low temperature of -40 ℃, the wheel surface is the roughest with the arithmetic mean roughness of 3.74. As the service temperature increases, the roughness of the wheel surface decreases significantly. At a high temperature of 60 ℃, the roughness of the wheel surface is small, and arithmetic mean roughness is 0.97. As the service temperature increases, the element content ratios of the Fe to O in the wear area of the wheel-rail contact interface decrease gradually. A low-temperature and low-humidity environment inhibits the frictional oxidation of the wheel-rail interface, enhances the frictional shear, aggravates the delamination on the wheel surface and serious plastic deformation, and promotes the initiation and propagation of surface fatigue cracks. Therefore, the wear surface is relatively rough. However, the high-temperature environment accelerates the frictional oxidation of the wheel-rail interface, and the formation of oxidized debris plays a solid lubrication role. Therefore, the adhesion of wheel-rail interface reduces, and the wheel surface is relatively smooth. The wear mechanism gradually changes from the fatigue wear at low temperature (-50 ℃~-20 ℃) to the abrasive wear and oxidation wear at room temperature (20 ℃), and adhesive wear at high temperature (40 ℃~60 ℃). © 2021, Editorial Department of Journal of Traffic and Transportation Engineering. All right reserved.
引用
下载
收藏
页码：269 / 278
页数：9
相关论文
共 32 条
  • [11] MA L, GUO J, LIU Q Y, Et al., Fatigue crack growth and damage characteristics of high-speed rail at low ambient temperature, Engineering Failure Analysis, 82, pp. 802-815, (2017)
  • [12] EKBERG A, KABO E., Fatigue of railway wheels and rails under rolling contact and thermal loading-an overview, Wear, 258, 7, pp. 1288-1300, (2005)
  • [13] ALIZADEH OTORABAD H, YOUNESIAN D, HOSSEINI TEHRANI P, Et al., Modeling temperature evolution of wheel flat during formation, International Journal of Thermal Sciences, 140, pp. 114-126, (2019)
  • [14] LEBEDEV V I, TSAREV V F, MOGIL'NYJ V V, Et al., Experience of railroad rail production intended for service at low temperatures, Steel, 12, pp. 26-27, (1997)
  • [15] PARSHIN V A, REJKHART V A., Increase of low temperature rail service reliability, Steel, 6, pp. 55-58, (1993)
  • [16] YUR'EV A B, GODIK L A, KOZYREV N A, Et al., Using Nitrovan alloy in the production of low-temperature rail steel, Steel in Translation, 38, 9, pp. 756-758, (2008)
  • [17] FANG Xiu-yang, CAI Zhen-bing, WANG Jun-guo, Et al., Evaluation of temperature-sensitive fatigue crack propagation of a high-speed railway wheel rim material, Fatigue and Fracture of Engineering Materials and Structures, 42, 8, pp. 1815-1825, (2019)
  • [18] FANG Xiu-yang, ZHAO Yong-xiang, LIU Huan-wei, Study on fatigue failure mechanism at various temperatures of a high-speed railway wheel steel, Materials Science and Engineering: A, 696, pp. 299-314, (2017)
  • [19] WHITE B, LEWIS R., Simulation and understanding the wet-rail phenomenon using twin disc testing, Tribology International, 136, pp. 475-486, (2019)
  • [20] WANG Ping, GUO Qiang, CHEN Jia-yin, Et al., Research on the effect of wheel-rail lubrication on curved switch rail wear in high-speed turnout, Journal of Railway Engineering Society, 36, 9, pp. 17-22, (2019)
1234