Research on Wear and Electrochemical Corrosion Properties of Laser Cladding Nickel Base Alloy

被引：0
|
作者：
Han C.-Y. [1 ]
Sun Y.-N. [1 ]
Xu Y.-F. [1 ]
Zhang R.-H. [2 ]
Lu C. [3 ]
Zhao F. [4 ]
机构：
[1] School of Mechanical Engineering, Xinjiang University, Urumqi
[2] Yangjiang Hardware Knife and Scissors Industrial Technology Research Institute, Yangjiang
[3] General Iron and Steel Research Institute, Beijing
[4] Lanzhou University of Technology, Lanzhou
来源：
Surface Technology | 2021年 / 50卷 / 11期
关键词：
corrosion; hardness; laser technique; microstructure; nickel base alloy; wear resisting;
D O I：
10.16490/j.cnki.issn.1001-3660.2021.11.008
中图分类号：
学科分类号：
摘要：
In order to solve the problem that the service life of surface layer of stainless steel parts is shortened due to wear and corrosion in engineering practice, efforts are made to repair and improve the hardness, wear resistance and corrosion resistance of surface layer of stainless steel. On the basis of summarizing a lot of experimental data and rules in the early stage, Ni60 coating with good cladding quality and no cracks was prepared on 304 stainless steel surface by laser cladding. The microstructure, element distribution and phase structure of the cladding surface were systematically studied by optical microscope, scanning electron microscope, energy dispersive spectrometer and X-ray diffractometer. The hardness distribution, wear characteristics and electrochemical characteristics of the cladding surface were measured by microhardness tester, friction and wear tester and electrochemical workstation. The uniform and compact microstructure of the coating is mainly composed of solid solution state γ-(Ni,Fe), carbides M23C6 (M=Fe, Ni, Cr) and boride CrB. The microhardness of the cladding coating is about 2.5 times that of the substrate. The hardness enhancement of the coating is mainly caused by the hard reinforcing phase formed in the cladding process. The wear rate, wear depth and wear surface roughness per unit area (Sa) of the cladding coating are 8.5%, 69% and 22.2% of the substrate, respectively. Compared with the substrate, the wear resistance of the cladding coating is obviously better. The corrosion rate of the coating is 2 orders of magnitude lower than that of the substrate, and the formation of dense passivation film on the coating surface is the main reason for the good corrosion resistance. Compared with 304 austenitic stainless steel base material, Ni60 coating with good cladding quality has better hardness, wear resistance and corrosion resistance. © 2021, Chongqing Wujiu Periodicals Press. All rights reserved.
引用
收藏
页码：103 / 110
页数：7
相关论文
共 25 条
  • [21] SUI Yi-yong, YANG Fan, QIN Guo-liang, Et al., Micro-structure and wear resistance of laser-cladded Ni-based composite coatings on downhole tools, Journal of materials processing technology, 252, pp. 217-224, (2018)
  • [22] SUN Yuan, ZHAO Xu, SU Jin, Et al., Microstructure and properties of nickel-based single crystal superalloy brazed joints, Transactions of the China Welding Institution, 41, 7, pp. 32-38, (2020)
  • [23] LI Ning, WANG Gang, WANG Ting, Et al., Weldability of Inconel 718 and 304 stainless steel by electron beam welding, Transactions of the China Welding Institution, 40, 2, pp. 82-85, (2019)
  • [24] HUANG Jie, HE Ding-yong, DU Kai-ping, Et al., Micro-structure and electrochemical corrosion behavior of FeCrNiMo layer fabricated by laser cladding, Surface technology, 49, 12, pp. 228-234, (2020)
  • [25] TAN Jin-hua, SUN Rong-lu, NIU Wei, Et al., Effect of Ni60/h-BN content on microstructures and properties of laser cladding titanium-based composite coatings, Surface technology, 48, 10, pp. 107-115, (2019)
123