Experimental dynamical analysis and numerical simulation of the material properties of parts made by fused deposition modelling technologies

被引：0
|
作者：
Ficzere P. [1 ]
机构：
[1] Department of Vehicle Elements and Vehicle-Structure Analysis, Faculty of Transportation Engineering and Vehicle Engineering, Budapest University of Technology and Economics, Műegyetem rakpart 3, Budapest
来源：
Periodica Polytechnica Transportation Engineering | 2020年 / 48卷 / 03期
关键词：
Additive manufacturing; Eigenfrequency; Experimental modal analysis; Material law; Mode shapes; Polymers;
D O I：
10.3311/PPTR.13947
中图分类号：
学科分类号：
摘要：
In the recent years 3D printing became a hot topic, however it's hard to design parts without a deep understanding of the material properties. The usage of these materials in vehicles assumes the knowledge of the behavior in dynamical environment. The aim of this study is to estimate the modal parameters and the damping properties via experimental dynamic analysis of a part made from PLA. With the results we can provide data for the FEM softwares' input. After the numerical simulations the simulated results were compared to the measured data. © 2020 Budapest University of Technology and Economics. All rights reserved.
引用
收藏
页码：221 / 225
页数：4
相关论文
共 50 条
  • [31] Experimental Study of the Effect of Post Processing Techniques on Mechanical Properties of Fused Deposition Modelled Parts
    Rao, Addanki Sambasiva
    Dharap, Medha A.
    Venkatesh, J. V. L.
    INTERNATIONAL JOURNAL OF MANUFACTURING MATERIALS AND MECHANICAL ENGINEERING, 2015, 5 (01) : 1 - 20
  • [32] Tribological Properties of Fe-Nylon6 Composite Parts Prepared Using Fused Deposition Modelling
    Garg, Harish
    Singh, Rupinder
    TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS, 2017, 70 (05) : 1241 - 1244
  • [33] Effect of fused deposition modelling process parameters on mechanical properties of 3D printed parts
    Chadha, Abhinav
    Ul Haq, Mir Irfan
    Raina, Ankush
    Singh, Rana Ratna
    Penumarti, Narendra Babu
    Bishnoi, Manjeet Singh
    WORLD JOURNAL OF ENGINEERING, 2019, 16 (04) : 550 - 559
  • [34] Tribological Properties of Fe–Nylon6 Composite Parts Prepared Using Fused Deposition Modelling
    Harish Garg
    Rupinder Singh
    Transactions of the Indian Institute of Metals, 2017, 70 : 1241 - 1244
  • [35] Experimental investigation on mechanical properties of PETG material processed by fused deposition modeling method
    Durgashyam, K.
    Reddy, M. Indra
    Balakrishna, A.
    Satyanarayana, K.
    MATERIALS TODAY-PROCEEDINGS, 2019, 18 : 2052 - 2059
  • [36] Experimental study of wax-material support structure for fused deposition modeling printed parts with overhanging sections
    Mukhtarkhanov M.
    Shehab E.
    Araby S.
    Ali M.H.
    International Journal of Lightweight Materials and Manufacture, 2023, 6 (04) : 534 - 542
  • [37] STUDY BY NUMERICAL-SIMULATION OF THE STRUCTURAL AND DYNAMICAL PROPERTIES OF THE FUSED LICL-KCL EUTECTIC
    LANTELME, F
    TURQ, P
    ZEITSCHRIFT FUR NATURFORSCHUNG SECTION A-A JOURNAL OF PHYSICAL SCIENCES, 1984, 39 (02): : 162 - 168
  • [38] Prediction and analysis of sliding wear performance of fused deposition modelling-processed ABS plastic parts
    Equbal, A.
    Sood, A. K.
    Toppo, V.
    Ohdar, R. K.
    Mahapatra, S. S.
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART J-JOURNAL OF ENGINEERING TRIBOLOGY, 2010, 224 (J12) : 1261 - 1271
  • [39] EXPERIMENTAL EVALUATION OF THE DAMPING PROPERTIES AND OPTIMAL MODELLING OF COATINGS MADE BY PLASMA DEPOSITION TECHNIQUES
    Amadori, Stefano
    Catania, Giuseppe
    PROCEEDINGS OF THE 7TH INTERNATIONAL CONFERENCE ON MECHANICS AND MATERIALS IN DESIGN (M2D2017), 2017, : 313 - 324
  • [40] The improvement of mechanical and thermal properties of polyamide 12 3D printed parts by fused deposition modelling
    Rahim, T. N. A. T.
    Abdullah, A. M.
    Akil, H. Md
    Mohamad, D.
    Rajion, Z. A.
    EXPRESS POLYMER LETTERS, 2017, 11 (12): : 963 - 982
12345