Structural and mechanical properties of Cu-SiCp nanocomposites fabricated by accumulative roll bonding (ARB)

被引:1
|
作者
Ghaderi, Omid [1 ]
Zare, Mehran [1 ]
Sadabadi, Hamed [1 ]
Toroghinejad, Mohammad Reza [2 ]
Najafizadeh, Abbas [2 ]
Church, Benjamin C. [1 ]
Rohatgi, Pradeep K. [1 ]
机构
[1] Univ Wisconsin, Dept Mat Sci & Engn, Milwaukee, WI 53211 USA
[2] Isfahan Univ Technol, Dept Mat Engn, Esfahan, Iran
来源
FRONTIERS IN MATERIALS | 2024年 / 11卷
关键词
copper-silicon carbide composite; accumulative roll bonding (ARB); microstructure; mechanical properties; fractography; texture parameter; reitveld method; SEVERE PLASTIC-DEFORMATION; MATRIX COMPOSITES; SHEAR STRAIN; GRAIN-SIZE; MICROSTRUCTURE; EVOLUTION; ALUMINUM; STRENGTH; TEXTURE; ALLOYS;
D O I
10.3389/fmats.2024.1362746
中图分类号
T [工业技术];
学科分类号
08 ;
摘要
In this study, the accumulative roll bonding (ARB) method, a severe plastic deformation (SPD) process, was used to fabricate copper-2 wt% silicon carbide composite strips. The ARB process was successfully conducted for up to nine cycles on pure copper strips with silicon carbide particles distributed between them, as well as on monolithic copper. Equiaxed tensile and Vickers hardness tests were conducted to evaluate the mechanical properties of the samples. SEM was utilized to study the fracture surfaces and to determine the fracture mechanism of ARB processed monolithic copper and composite samples after the tensile test. Texture parameters were calculated through X-ray analysis. The Rietveld method using MAUD software were employed to assess the crystallite size of the samples. Results indicated that average amount of porosity decreased and interface bonding between copper strip layers improved with increasing the number of ARB cycles. Moreover, an increased number of cycles led to homogeneous distribution of SiC particles within the copper matrix. The tensile strength of the fabricated composites improved with an increase in the number of cycles, ultimately reaching 483 MPa after nine cycles, compared to 388 MPa for the composite processed with a single cycle of ARB and 194 MPa for annealed copper strips. Initially, the elongation of the composite samples decreased dramatically to about 6% after applying five cycle of ARB process from the 46% observed for annealed pure copper strip. However, it improved as the process continued, reaching 8.9% after the ninth cycle. Investigation of fracture surfaces after the tensile test using SEM revealed that the dominant failure mode was shear ductile fracture. Analysis of sample textures demonstrated that the dominant texture was (100). Crystallite sizes for pure copper and nine cycles-rolled composites, as determined by Reitveld method, reached 111 nm and 89 nm, respectively.
引用
收藏
页数:16
相关论文
共 50 条
  • [11] Accumulative roll bonding (ARB) and Cross accumulative roll bonding (CARB) in aluminum: A review
    Trajano, Adriano A.
    Correa, Elaine Carballo Siqueira
    Aguilar, Maria Teresa P.
    Cetlin, Paulo Roberto
    MATERIALS SCIENCE AND TECHNOLOGY, 2024,
  • [12] Mechanical and microstructural investigation of Zn/Sn multilayered composites fabricated by accumulative roll bonding (ARB) process
    Mashhadi, Amir
    Atrian, Amir
    Ghalandari, Laleh
    Journal of Alloys and Compounds, 2017, 727 : 1314 - 1323
  • [13] Mechanical and microstructural investigation of Zn/Sn multilayered composites fabricated by accumulative roll bonding (ARB) process
    Mashhadi, Amir
    Atrian, Amir
    Ghalandari, Laleh
    JOURNAL OF ALLOYS AND COMPOUNDS, 2017, 727 : 1314 - 1323
  • [14] Fabrication of nanostructure Al/SiCP composite by accumulative roll-bonding (ARB) process
    Alizadeh, M.
    Paydar, M. H.
    JOURNAL OF ALLOYS AND COMPOUNDS, 2010, 492 (1-2) : 231 - 235
  • [15] Structural characteristics of Cu/Ti bimetal composite produced by accumulative roll-bonding (ARB)
    Hosseini, M.
    Pardis, N.
    Manesh, H. Danesh
    Abbasi, Majid
    Kim, Dong-Ik
    MATERIALS & DESIGN, 2017, 113 : 128 - 136
  • [16] Study on mechanical and magnetic properties of Cu/Ni multilayer composite fabricated by accumulative roll bonding process
    Eslami, A. H.
    Zebarjad, S. Mojtaba
    Moshksar, M. M.
    MATERIALS SCIENCE AND TECHNOLOGY, 2013, 29 (08) : 1000 - 1005
  • [17] Microstructure and mechanical properties of laminated Al-Cu-Mg composite fabricated by accumulative roll bonding
    Motevalli, Parisa Darvish
    Eghbali, Beitallah
    BULLETIN OF MATERIALS SCIENCE, 2017, 40 (07) : 1481 - 1488
  • [18] On the microstructure, texture and mechanical properties through heat treatment in Al-CuO nanocomposite fabricated by Accumulative Roll Bonding (ARB)
    Roghani, H.
    Borhani, E.
    Shams, S. A. A.
    Lee, C. S.
    Jafarian, H. R.
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2021, 828
  • [19] Microstructure and mechanical properties of Ni/Ti/Al/Cu composite produced by accumulative roll bonding (ARB) at room temperature
    Ye, Nan
    Ren, Xueping
    Liang, Juhua
    JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T, 2020, 9 (03): : 5524 - 5532
  • [20] Mechanical alloying process and mechanical properties of Cu-SiCp composite
    Gan, K. K.
    Gu, M. Y.
    MATERIALS SCIENCE AND TECHNOLOGY, 2006, 22 (08) : 960 - 964