Position detection system of shearer based on combined measurement of multiple sensing modes

被引:0
|
作者
Zhang Z. [1 ]
Fu S. [1 ]
Liu C. [1 ]
Li Y. [1 ]
Lan Y. [1 ]
Wu M. [1 ]
机构
[1] School of Mechanical Electronic and Information Engineering, China University of Mining and Technology-Beijing, Beijing
来源
Meitan Kexue Jishu/Coal Science and Technology (Peking) | 2021年 / 49卷 / 11期
关键词
Combined measurement; Inclination sensor; North finder; Pose detection; Shearer; Total station; UWB system;
D O I
10.13199/j.cnki.cst.2021.11.028
中图分类号
学科分类号
摘要
In recent years, safety accidents such as underground gas explosions and water penetration have occurred frequently, seriously threatening the lives of miners. In order to achieve the unmanned and high-precision detection of the shearer' s position in the fully mechanized coal mining face, improve the working environment of the miners, and increase the mechanization and automation of the coal mine, the real-time position of the coal mining machine in the existing comprehensive mining face was compared. Based on the technical method of attitude, a coal shearer attitude detection system based on combined measurement of multiple sensing methods was proposed.This system uses a combination of a total station and UWB (Ultra Wide-band) positioning system to measure the spatial position coordinates of the shearer. A combination of inclination sensor and a north seeker was used to measure the attitude angle (heading angle, roll angle, and pitch angle) of the shearer. In this paper, a three-dimensional model of the system was established. The total station was installed at the intersection of the section transportation lane and the transportation uphill, and the UWB fixed base station group was installed at the transfer machine at the intersection of the fully-mechanized working face and the section transportation lane. In order to realize the autonomous calibration of the UWB mobile base station when it moves, the UWB modules were installed at the top and bottom of the hydraulic support, the UWB positioning node was installed on the shearer body, and the inclination sensor and the north finder were installed on the shearer body. The measurement method of the coordinates of the total station and the UWB fixed base station group was deduced, and the CT (Caffery-Taylor) algorithm of the UWB positioning system based on the TOA (Time of Arrival) positioning model was deduced. The coordinate transformation matrix between the total station coordinate system and the UWB fixed base station group coordinate system was also calculated. The system structure and working principle of shearer inclination sensor and north finder were introduced in detail. The limited factors of this system in practical application were analyzed, and corresponding improvement schemes were briefly proposed. This system can theoretically realize the real-time posture and attitude detection of the shearer in the fully mechanized working face, which provides a theoretical reference for simulation analysis and experimental platform construction. © 2021 China Coal Society. All right reserved.
引用
收藏
页码:218 / 224
页数:6
相关论文
共 19 条
  • [11] Shichen FL, Research on position detection method of cantilever tunneling machine based on LWB ranging, pp. 39-60, (2018)
  • [12] YANG Zhou, WANG Yunjia, EN Guoliang Cn, Research on LWB indoor high precision positioning technology '[J], Journal of Navigation and Positioning, 32, 4, pp. 31-35, (2014)
  • [13] Shichen FL, Yiming Ll, YANG Jianjian, Research on autonomous positioning and orientation method of roadheader based on LWB technology [J], Journal of China Coal Society, 40, 11, pp. 2603-2610, (2015)
  • [14] FL Shichen, Yiming Ll, ZHANG Minjun, Et al., Experimental study on accuracy test of TW - TOF ranging technology based on LWB signal in narrow and long roadway [J], Coal Technology, 36, 3, pp. 246-249, (2017)
  • [15] AN Yuan Tl, Exploration on automatic guidance and positioning technology of cantilever tunneling machine[J], lndustry and Mine Automation, 36, 8, pp. 26-29, (2010)
  • [16] CAFFERY J., A new approach to the geometry of TOA location [J], lEEE Trans.SP, 42, 8, pp. 1905-1915, (1994)
  • [17] Li Ll, Ping DENG, Lin LlL, Taylor series expansion method and its performance analysis[J], Journal of Southwest Jiaotong university, 37, 6, pp. 684-688, (2002)
  • [18] FOY W H., Position-location solutions by taylor-series estimation [J], lEEE Trans, 12, 2, pp. 187-194, (1796)
  • [19] Zhiyu XlE, Xiongfei LlL, Zhikun HL, Research and implementation of LWB downhole positioning algorithm based on Taylor expansion [J], Computer Engineering and Applications, 5, pp. 231-235, (2017)