PARAMETRIC STUDIES OF BEARING STRENGTH FOR FIBER METAL LAMINATES

被引：9
|
作者：
WU, HF
SLAGTER, WJ
机构：
[1] Alcoa Technical Center, Alcoa Center, Pennsylvania
[2] Delft University of Technology, Delft
[3] Product Design and Mechanics Division, Owens-Corning Science and Technology Center, Granville, OH
来源：
JOURNAL OF AIRCRAFT | 1994年 / 31卷 / 04期
关键词：
D O I：
10.2514/3.46582
中图分类号：
V [航空、航天];
学科分类号：
08 ; 0825 ;
摘要：
An experimental program based on statistical design was conducted to establish a meaningful test procedure for determination of fiber/metal laminate bearing strength design allowables. The test procedures investigated are the pin-type bearing test method (ASTM E-238) and the bolt-type bearing test method, a modified method based on procedure for bearing strength determinations in plastics (ASTM D-953). Results are presented from an experimental program which measured the bearing strengths of two grades of S-2 glass fiber-based and one grade or aramid fiber-based aluminum laminates. The influences or lateral constraint and ply orientation on bearing strength and failure mode are observed. The bolt-type bearing test method which combines the attributes of two aforementioned methods is recommended. The study also showed that bearing properties of edge distance ratio equals to 2 can be predicted by correlation with the aluminum volume fraction in fiber-reinforced aluminum laminates. In addition, diagrams of joint structural efficiency shown to be comparable with aluminum alloy sheets have been established.
引用
收藏
页码：936 / 945
页数：10
相关论文
共 50 条
  • [11] Bearing strength of commingled boron/glass fiber reinforced aluminum laminates
    Yeh, Po-Ching
    Chang, Po-Yu
    Wang, Justin
    Yang, Jenn-Ming
    Wu, Peter H.
    Liu, Ming C.
    COMPOSITE STRUCTURES, 2012, 94 (11) : 3160 - 3173
  • [12] Theory and Experiment in Predicting the Strength of Hybrid Fiber Metal Laminates
    Babanli, Mustafa
    Turen, Yunus
    Gurbanov, Nurlan
    Mehtiyev, Rafail
    Askin, Mustafa Yunus
    Ismayilov, Mahmud
    JOURNAL OF APPLIED AND COMPUTATIONAL MECHANICS, 2023, 9 (04): : 987 - 999
  • [13] Residual strength of centrally cracked metal/fiber composite laminates
    Jin, ZH
    Batra, RC
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 1996, 216 (1-2): : 117 - 124
  • [14] Bolt Bearing Strength of Commingled Boron/Glass Fiber Reinforced Aluminum Laminates
    Yeh, P. C.
    Chang, P. Y.
    Yang, J. M.
    Wu, P. H.
    Liu, M. C.
    INTERNATIONAL MECHANICAL ENGINEERING CONGRESS AND EXPOSITION - 2012, VOL 3, PTS A-C: DESIGN, MATERIALS, AND MANUFACTURING, 2013, : 1167 - 1178
  • [15] Enhancing interfacial bonding strength in fiber metal laminates through metal surface treatments
    Liu, Zheng
    Simonetto, Enrico
    Umbrello, Domenico
    Rotella, Giovanna
    MATERIAL FORMING, ESAFORM 2024, 2024, 41 : 2057 - 2064
  • [16] Estimating the failure strength of fiber metal laminates by using a hybrid degradation model
    Department of Mechanical Engineering, Vignan University, Guntur, India
    不详
    J Reinf Plast Compos, 20 (3058-3063):
  • [17] Estimating the failure strength of fiber metal laminates by using a hybrid degradation model
    Rao, Pavuluri M. V.
    Rao, V. V. Subba
    JOURNAL OF REINFORCED PLASTICS AND COMPOSITES, 2010, 29 (20) : 3058 - 3063
  • [18] ON THE TENSILE-STRENGTH OF RIVETS IN THIN SHEET MATERIALS AND FIBER METAL LAMINATES
    SLAGTER, WJ
    THIN-WALLED STRUCTURES, 1995, 21 (02) : 121 - 145
  • [19] Blunt notch strength of hybrid boron/glass/aluminum fiber metal laminates
    Yeh, Po-Ching
    Chang, Po-Yu
    Yang, Jenn-Ming
    Wu, Peter H.
    Liu, Ming C.
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2011, 528 (4-5): : 2164 - 2173
  • [20] ON THE BEARING STRENGTH OF BOLTED GRAPHITE EPOXY LAMINATES
    ERIKSSON, I
    JOURNAL OF COMPOSITE MATERIALS, 1990, 24 (12) : 1246 - 1269
12345