MORPHOLOGY OF INJECTION-MOLDED POLYPROPYLENE

被引：117
|
作者：
FITCHMUN, DR [1 ]
MENCIK, Z [1 ]
机构：
[1] FORD MOTOR CO,SCI RES STAFF,DEARBORN,MI 48121
来源：
JOURNAL OF POLYMER SCIENCE PART B-POLYMER PHYSICS | 1973年 / 11卷 / 05期
关键词：
D O I：
10.1002/pol.1973.180110512
中图分类号：
O63 [高分子化学（高聚物）];
学科分类号：
070305 ; 080501 ; 081704 ;
摘要：
引用
收藏
页码：951 / 971
页数：21
相关论文
共 50 条
  • [21] Crystallization of Polypropylene Near the Surface in Injection-Molded Plaques: A Comparison of Morphology and a Numerical Analysis
    Kobayashi, Yutaka
    Otsuki, Yasuhiko
    Kanno, Hiroaki
    Sasakawa, Tomoyoshi
    Hanamoto, Yasuhiro
    Kanai, Toshitaka
    POLYMER ENGINEERING AND SCIENCE, 2011, 51 (07): : 1236 - 1244
  • [22] Measuring and Simulating Morphology Gradients in Injection-Molded Talc-Reinforced Isotactic Polypropylene
    Granlund, Havard
    Andreassen, Erik
    Skjonsfjell, Eirik Torbjorn Bakken
    Hoydalsvik, Kristin
    Diaz, Ana
    Breiby, Dag Werner
    JOURNAL OF POLYMER SCIENCE PART B-POLYMER PHYSICS, 2014, 52 (17) : 1157 - 1167
  • [23] Effect of the holding pressure on the skin-core morphology of injection-molded polypropylene parts
    1600, (39):
  • [24] EFFECT OF THE HOLDING PRESSURE ON THE SKIN-CORE MORPHOLOGY OF INJECTION-MOLDED POLYPROPYLENE PARTS
    TROTIGNON, JP
    VERDU, J
    JOURNAL OF APPLIED POLYMER SCIENCE, 1990, 39 (05) : 1215 - 1217
  • [25] Morphology and properties of injection-molded nylon 1010
    Dai, Wenli
    Xue, Liang
    Wang, Pengju
    Gaofenzi Cailiao Kexue Yu Gongcheng/Polymeric Materials Science and Engineering, 1996, 12 (01): : 116 - 119
  • [26] Mechanisms of fatigue fracture in injection-molded polypropylene sheets
    Miyaji, T
    Kawagoe, M
    Qiu, JH
    Morita, M
    Mizuno, W
    KOBUNSHI RONBUNSHU, 1999, 56 (03) : 133 - 140
  • [27] GAMMA-PHASE IN INJECTION-MOLDED ISOTACTIC POLYPROPYLENE
    KALAY, G
    ALLAN, P
    BEVIS, MJ
    POLYMER, 1994, 35 (12) : 2480 - 2482
  • [28] MICROSTRUCTURE AND PHYSICAL PROPERTY CONTROL OF INJECTION-MOLDED POLYPROPYLENE
    KALAY, G
    ALLAN, P
    BEVIS, MJ
    PLASTICS RUBBER AND COMPOSITES PROCESSING AND APPLICATIONS, 1995, 23 (02): : 71 - 85
  • [29] Crystal orientation distributions in injection-molded polypropylene compounds
    Chen, Z.
    Finet, M.C.
    Liddell, K.
    Thompson, D.P.
    White, J.R.
    Journal of Applied Polymer Science, 1992, 46 (08): : 1429 - 1437
  • [30] MORPHOLOGY OF INJECTION-MOLDED POLYOLEFINE GATE ZONES
    KRSOVA, A
    NEUHAUSL, E
    JOURNAL OF MATERIALS SCIENCE LETTERS, 1989, 8 (04) : 376 - 380
12345