CUTTING PERFORMANCE OF A CEMENTED CARBIDE DRILL WITH 3 CUTTING EDGES

被引：1

作者：

EMA, S

MARUI, E

机构：

[1] Faculty of Education, Gifu University, Gifu-shi, IL, 501-11, 1-1, Yanagido

[2] Faculty of Engineering, Gifu University, Gifu-shi, IL, 501-11, 1-1, Yanagido

来源：

JOURNAL OF ENGINEERING FOR INDUSTRY-TRANSACTIONS OF THE ASME | 1992年 / 114卷 / 01期

关键词：

D O I：

10.1115/1.2899748

中图分类号：

TH [机械、仪表工业];

学科分类号：

0802 ;

摘要：

In this paper, an investigation of the cutting performance of a cemented carbide drill with three cutting edges is reported. Drilling tests were performed in which the eccentricity, straightness, cylindricity, and roundness of machined holes were measured using the least squares technique. Surface roughness was also measured. The investigation showed that the cemented carbide drill with three cutting edges is more effective than a conventional drill with two cutting edges, except for cylindricity.

引用

页码：116 / 119

页数：4

共 50 条

[41] DYNAMICS OF DRILL BITS WITH CUTTING EDGES OF VARYING PARAMETERS
Dombovari, Zoltan
Stepan, Gabor
PROCEEDINGS OF THE ASME INTERNATIONAL DESIGN ENGINEERING TECHNICAL CONFERENCES AND COMPUTERS AND INFORMATION IN ENGINEERING CONFERENCE, 2013, VOL 7B, 2014,
[42] Wear behavior and cutting performance of CrAlSiN and TiAlSiN hard coatings on cemented carbide cutting tools for Ti alloys
Chang, Yin-Yu
Lai, Hsing-Ming
SURFACE & COATINGS TECHNOLOGY, 2014, 259 : 152 - 158
[43] Evaluation of performance of uncoated cemented carbide cutting tools at longitudinal turning at cutting velocity 3?500 m/min and influence of coating
Vasilko, Karol
Murcinkova, Zuzana
Murcinko, Jaromir
MATERIALS TODAY-PROCEEDINGS, 2021, 44 : 2575 - 2580
[44] The effects of grinding process parameters of a cemented carbide micro-drill on cutting edge burr formation
Xiong, Qiang
Yan, Qiusheng
Lu, Jiabin
Pan, Jisheng
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2021, 117 (9-10): : 3041 - 3051
[45] The effects of grinding process parameters of a cemented carbide micro-drill on cutting edge burr formation
Qiang Xiong
Qiusheng Yan
Jiabin Lu
Jisheng Pan
The International Journal of Advanced Manufacturing Technology, 2021, 117 : 3041 - 3051
[46] Experiment on cutting performance of textured cemented carbide tools with various wettability levels
Xiuqing Hao
Hanlong Li
Yinfei Yang
Sinong Xiao
Xiaolu Song
Liang Li
The International Journal of Advanced Manufacturing Technology, 2019, 103 : 757 - 768
[47] Experimental research on ELID grinding and cutting performance of nano cemented carbide cutters
Zhang, FH
Gui, JC
Liu, YZ
Zhang, HL
ADVANCES IN ABRASIVE TECHNOLOGY VIII, 2005, 291-292 : 115 - 120
[48] Cutting performance of cemented carbide tools with nano-crystalline pvd coatings
Hudecek, Pavel
Dostal, Petr
MENDELNET 2014, 2014, : 542 - 546
[49] Effect of the crystallinity of diamond coatings on cemented carbide inserts on their cutting performance in milling
Skordaris, G.
Bouzakis, K-D
Kotsanis, T.
Boumpakis, A.
Stergioudi, E.
Christofilos, D.
Lemmer, O.
Koelker, W.
Woda, M.
CIRP ANNALS-MANUFACTURING TECHNOLOGY, 2019, 68 (01) : 65 - 68
[50] Effects of pretreatment on the performance of diamond-coated cemented carbide cutting tools
Wang, Q
Zhang, Q
Wang, SG
Yoon, SF
Ahn, J
Zhao, BQ
Tang, WZ
Miao, JQ
Lu, FX
JOURNAL OF VACUUM SCIENCE & TECHNOLOGY A, 2003, 21 (06): : 1939 - 1942

← 1 2 3 4 5 →