Influence of cutting parameters and tool geometry on surface roughness of SAE 40 bronze in turning operations

被引：0
|
作者：
Pereira, Juan C. F. [1 ]
Ruiz, Ruben G. [2 ]
机构：
[1] Univ Carabobo, Fac Ingn, Ctr Invest Mecan CIMEC, Escuela Ingn Mecan, Valencia, Venezuela
[2] Univ Carabobo, Fac Ingn, Escuela Ingn Mecan, Dept Mat & Proc Fabricac, Valencia, Venezuela
来源：
INGENIERIA UC | 2007年 / 14卷 / 03期
关键词：
Surface roughness; SAE; 40; bronze; turning;
D O I：
暂无
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
This paper describes the influence of cutting parameters and cutting tool geometry on the surface finish of SAE 40 Bronze in turning operations based on the experimental measurement of surface roughness. For the data analysis according to variables studied, 3-D behavior graphs and a multifactorial analysis of variance (ANOVA) were made. A digital surface roughness tester was used, and a factorial experimental design was made, which allowed turning bars of SAE 40 Bronze by means of a conventional lathe. A carbide insert with quadrangular geometry was used. The influence of cutting parameters such as feed rate, depth of cut and cutting speed, and the cutting tool geometry (nose radius) on the magnitude of the experimental surface roughness in turning operations was determined.
引用
收藏
页码：77 / 85
页数：9
相关论文
共 50 条
  • [1] Surface roughness prediction based on cutting parameters and tool vibrations in turning operations
    Abouelatta, OB
    Mádl, J
    [J]. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2001, 118 (1-3) : 269 - 277
  • [2] THE INFLUENCE OF THE CUTTING PARAMETERS ON THE SURFACE ROUGHNESS AND VIBRATION SIGNAL IN THE TURNING PROCESS
    Marinkovic, D.
    Antic, A.
    Knezev, M.
    Mladjenovic, C.
    Zivkovic, A.
    [J]. MM SCIENCE JOURNAL, 2024, 2024 : 7539 - 7544
  • [3] Influence of Cutting Parameters on Surface Roughness for Wet and Dry Turning Process
    Yusuf, Muhammad
    Anuar, Khairol
    Ismail, Napsiah
    Sulaiman, Shamsuddin
    [J]. COMPOSITE SCIENCE AND TECHNOLOGY, PTS 1 AND 2, 2011, 471-472 : 233 - 238
  • [4] Influence of cutting fluid conditions and cutting parameters on surface roughness and tool wear in turning process using Taguchi method
    Debnath, Sujan
    Reddy, Moola Mohan
    Yi, Qua Sok
    [J]. MEASUREMENT, 2016, 78 : 111 - 119
  • [5] Influence of Approaching Angle and Cutting Parameters on Cutting Forces, Tool Tip Temperature and Surface Roughness During Turning of Adamite
    Dhiman, Suresh
    Sharma, S. K.
    Sehgal, Rakesh
    Shama, Vishal S.
    [J]. JOURNAL FOR MANUFACTURING SCIENCE AND PRODUCTION, 2007, 8 (2-4) : 85 - 96
  • [6] Examination and modelling of the influence of cutting parameters on the cutting force and the surface roughness in longitudinal turning
    Bajic, Drazen
    Lela, Branimir
    Cukor, Goran
    [J]. STROJNISKI VESTNIK-JOURNAL OF MECHANICAL ENGINEERING, 2008, 54 (05): : 322 - 333
  • [7] On the prediction of surface roughness in the hard turning based on cutting parameters and tool vibrations
    Hessainia, Zahia
    Belbah, Ahmed
    Yallese, Mohamed Athmane
    Mabrouki, Tarek
    Rigal, Jean-Francois
    [J]. MEASUREMENT, 2013, 46 (05) : 1671 - 1681
  • [8] Optimization of tool geometry parameters for turning operations based on the response surface methodology
    Neseli, Suleyman
    Yaldiz, Suleyman
    Turkes, Erol
    [J]. MEASUREMENT, 2011, 44 (03) : 580 - 587
  • [9] Optimization of tool geometry and cutting parameters for hard turning
    Singh, Dilbag
    Rao, P. Venkateswara
    [J]. MATERIALS AND MANUFACTURING PROCESSES, 2007, 22 (01) : 15 - 21
  • [10] Influence of cutting parameters on cycle time, surface roughness, dimensional error and cutting forces in milling operations on aluminium 6082 sculptured surface geometry
    Quintana G.
    Gómez X.
    Delgado J.
    Ciurana J.
    [J]. International Journal of Machining and Machinability of Materials, 2010, 8 (3-4) : 339 - 355
12345