EVALUATION OF PIEZORESISTIVE COEFFICIENT VARIATION IN SILICON STRESS SENSORS USING A 4-POINT BENDING TEST FIXTURE

被引:77
|
作者
BEATY, RE [1 ]
JAEGER, RC [1 ]
SUHLING, JC [1 ]
JOHNSON, RW [1 ]
BUTLER, RD [1 ]
机构
[1] AUBURN UNIV,DEPT MECH ENGN,AUBURN,AL 36849
关键词
D O I
10.1109/33.180057
中图分类号
T [工业技术];
学科分类号
08 ;
摘要
In this paper, a study of the variation of the piezoresistive coefficients from several rosettes on the same die, the same wafer, and finally at different doping levels across a number of wafers has been presented. A thorough error analysis of the method of applying a known uniaxial state of stress using a four-point bending (4PB) fixture was completed. A sensor error analysis demonstrated that it is very difficult to determine accurate values for the sum (pi11 + pi12) using the common two-element rosette, particularly in p-type material. However, an empirical equation has been found that provides an estimate for this coefficient. The second piezoresistive coefficient pi44 can be measured accurately. However, the results presented for pi44 differ from those of previous authors by some 33%. Thus it appears necessary to measure this value for a given wafer lot.
引用
收藏
页码:904 / 914
页数:11
相关论文
共 50 条
  • [1] FE evaluation of 4-point bending test for fatigue cracking assessment
    Coni, M.
    Portas, S.
    Isola, R.
    Oliveira, J. R. M.
    [J]. PAVEMENT CRACKING: MECHANISMS, MODELING, DETECTION, TESTING AND CASE HISTORIES, 2008, : 271 - +
  • [2] Stress distribution in a 4-point or 3-point bending probe
    Meyer-Piening, HR
    [J]. MECHANICS OF SANDWICH STRUCTURES, 1998, : 105 - 112
  • [3] A detailed FEM simulation of a 4-point bending test device
    Huurman, M.
    Pronk, A. C.
    [J]. FOUR-POINT BENDING, 2012, : 3 - 12
  • [4] BRITTLE RING TEST - A COMPARISON WITH THE 3-POINT AND 4-POINT BENDING TESTS
    FREY, T
    GROZ, K
    HOLLER, J
    ZEHM, K
    [J]. CFI-CERAMIC FORUM INTERNATIONAL, 1995, 72 (06): : 333 - 337
  • [5] Adhesion investigation of low-k films system using 4-point bending test
    Lee, Chang-Chun
    Huang, Jacky
    Chang, Shu-Tong
    Wang, Wei-Ching
    [J]. THIN SOLID FILMS, 2009, 517 (17) : 4875 - 4878
  • [6] Calibration of a-2-D piezoresistive stress sensor in (100) silicon using a 4PB fixture
    Zhong, ZW
    Sim, BH
    Zhang, XW
    [J]. MEMS/MOEMS: ADVANCES IN PHOTONIC COMMUNICATIONS, SENSING, METROLOGY, PACKAGING AND ASSEMBLY, 2003, 4945 : 155 - 158
  • [7] TEST GEOMETRY AND ITS EFFECT ON GRAPHITE FLEXURAL STRENGTHS IN 4-POINT BENDING
    LEWALLEN, SF
    MORRIS, EG
    [J]. CARBON, 1982, 20 (02) : 154 - 154
  • [8] MEASUREMENT OF STRESS-DISTRIBUTION IN SANDWICH BEAMS UNDER 4-POINT BENDING
    KEMMOCHI, K
    UEMURA, M
    [J]. EXPERIMENTAL MECHANICS, 1980, 20 (03) : 80 - 86
  • [9] Study of the mechanical stress impact on silicide contact resistance by 4-point bending
    Liu, Yefan
    Yu, Hao
    Hiblot, Gaspard
    Kruv, Anastasiia
    Schaekers, Marc
    Horiguchi, Naoto
    Velenis, Dimitrios
    De Wolf, Ingrid
    [J]. 2019 IEEE INTERNATIONAL RELIABILITY PHYSICS SYMPOSIUM (IRPS), 2019,
  • [10] Measurement of stress distributions on silicon IC chips using piezoresistive sensors
    Suhling, JC
    Jaeger, RC
    [J]. NONTRADITIONAL METHODS OF SENSING STRESS, STRAIN, AND DAMAGE IN MATERIALS AND STRUCTURES: SECOND VOLUME, 2001, 1323 : 127 - 152