Using orthogonal experimental method optimizing surface quality of CO2 laser cutting process for PMMA microchannels

被引：0
|
作者：
Xueye Chen
Tiechuan Li
Ke zhai
Zengliang Hu
Mengde Zhou
机构：
[1] Liaoning University of Technology,Faculty of Mechanical Engineering and Automation
来源：
The International Journal of Advanced Manufacturing Technology | 2017年 / 88卷
关键词：
CO; laser; Polymer sheet; PMMA sheet; Orthogonal test method; Arithmetical mean roughness;
D O I：
暂无
中图分类号：
学科分类号：
摘要：
CO2 laser cutting is an advanced processing technology, which can, according to the computer-aided design graphics, cut a variety of shapes in the surfaces of many polymer sheets. This work aims to analyze the effect of laser power, scanning speed, and processing times on the surface roughness of polymethyl-methacrylate microchannels with CO2 laser LCJG-1290 cutting process. There are several experiments designed by us, and the results were analyzed by orthogonal experimental method. Finally, optimal power, scanning speed, and processing times were obtained, and in the optimal case, the arithmetical mean roughness (Ra) can reach as small as 110 nm.
引用
收藏
页码：2727 / 2733
页数：6
相关论文
共 50 条
  • [1] Using orthogonal experimental method optimizing surface quality of CO2 laser cutting process for PMMA microchannels
    Chen, Xueye
    Li, Tiechuan
    Zhai, Ke
    Hu, Zengliang
    Zhou, Mengde
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2017, 88 (9-12): : 2727 - 2733
  • [2] Assessment and Optimization of CO2 Laser Cutting Process of PMMA
    Eltawahni, H. A.
    Olabi, A. G.
    Benyounis, K. Y.
    INTERNATIONAL CONFERENCE ON ADVANCES IN MATERIALS AND PROCESSING TECHNOLOGIES, PTS ONE AND TWO, 2010, 1315 : 1553 - 1558
  • [3] Fabrication of microchannels on PMMA using a low power CO2 laser
    Imran, Muhammad
    Rahman, Rosly A.
    Ahmad, Mukhtar
    Akhtar, Majid N.
    Usman, Arslan
    Sattar, Abdul
    LASER PHYSICS, 2016, 26 (09)
  • [4] Evaluation of cutting quality of PMMA using CO2 lasers
    J. Paulo Davim
    Carlos Oliveira
    Nuno Barricas
    Marta Conceição
    The International Journal of Advanced Manufacturing Technology, 2008, 35 : 875 - 879
  • [5] Evaluation of cutting quality of PMMA using CO2 lasers
    Davim, J. Paulo
    Oliveira, Carlos
    Barricas, Nuno
    Conceicao, Marta
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2008, 35 (9-10): : 875 - 879
  • [6] Prediction of Kerf and Groove Widths in CO2 Laser Cutting Process of PMMA Using Experimental and Machine Learning Methods
    Aydin, K.
    Ugur, L.
    EXPERIMENTAL TECHNIQUES, 2025,
  • [7] Fabrication of microchannels on transparent PMMA using CO2 Laser (10.6 μm) for microfluidic applications: An experimental investigation
    Shashi Prakash
    Subrata Kumar
    International Journal of Precision Engineering and Manufacturing, 2015, 16 : 361 - 366
  • [8] Fabrication of Microchannels on Transparent PMMA Using CO2 Laser (10.6 μm) for Microfluidic Applications: An Experimental Investigation
    Prakash, Shashi
    Kumar, Subrata
    INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING, 2015, 16 (02) : 361 - 366
  • [9] Deep Engraving Process Of PMMA Using CO2 Laser Complemented By Taguchi Method
    Hubeatir, K. A.
    Al-Kafaji, M. M.
    Omran, H. J.
    INTERNATIONAL CONFERENCE ON MATERIALS ENGINEERING AND SCIENCE, 2018, 454
  • [10] A comparison of cutting speeds for the CO2 laser machining of PMMA
    Black, I
    LASERS IN ENGINEERING, 1999, 9 (03) : 221 - 227
12345