Effect of cutting parameters on surface roughness of waste-filled composite at milling

被引：0
|
作者：
Ozsoy, Murat [1 ]
Ozsoy, Neslihan [1 ]
Kilic, Cumhur [2 ]
Akinci, Akin [3 ]
机构：
[1] Sakarya Univ, Mech Engn Dept, Sakarya, Turkey
[2] Subor Pipe Co, Design Ctr, Sakarya, Turkey
[3] Sakarya Univ, Met & Mat Engn, Sakarya, Turkey
来源：
EMERGING MATERIALS RESEARCH | 2022年 / 11卷 / 01期
关键词：
composite structures; design; waste valorisation; OPTIMIZATION; METHODOLOGY; TAGUCHI; PLASTICS;
D O I：
10.1680/jemmr.21.00026
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
Industrial waste is a problem for companies as well as for the environment. In recent years, an alternative solution to this problem has been found - the use of waste in the production of new composite materials. It is not enough to produce only the composite. The machinability of the composite produced should also be investigated. This study obtained the new composite material using industrial waste produced by glass fibre-reinforced plastic pipes. The terephthalic resin was used as a matrix material. The waste powder was used as a filling material in the ratio of 30, 40 and 50% by weight compared to the matrix material. The machinability of produced composites was investigated according to three parameters with three levels. According to the experimental results, the optimum cutting parameters are obtained, depending on surface roughness.
引用
收藏
页码：12 / 18
页数：7
相关论文
共 50 条
  • [1] The Effect of Bamboo Surface Roughness of Cutting Parameters on the Bamboo Milling
    Liu, Yanhe
    Zhou, Jianbo
    Fu, Wansi
    Zhang, Bin
    Chang, Feihu
    Jiang, Pengfei
    [J]. BIORESOURCES, 2020, 15 (04) : 8323 - 8338
  • [2] Effect of Cutting Parameters on Surface Roughness in End Milling of AlSi/AlN Metal Matrix Composite
    Tomadi, S. H.
    Ghani, J. A.
    Haron, C. H. Che
    Ayu, H. Mas
    Daud, R.
    [J]. ADVANCES IN MATERIAL & PROCESSING TECHNOLOGIES CONFERENCE, 2017, 184 : 58 - 69
  • [3] Effect of Cutting Parameters On The Surface Roughness Of MWCNT Reinforced Epoxy Composite Using End-Milling Process
    Rao, G. Harii Krishna
    Ansari, M. N. M.
    [J]. NANOTECHNOLOGY 2012, VOL 1: ADVANCED MATERIALS, CNTS, PARTICLES, FILMS AND COMPOSITES, 2012, : 252 - 255
  • [4] Cutting parameters influence on surface roughness in AL 7075 milling
    Kosarac, Aleksandar
    Sikuljak, Lana
    Obradovic, Cedomir
    Mladenovic, Cvijetin
    Zeljkovic, Milan
    [J]. 2020 19TH INTERNATIONAL SYMPOSIUM INFOTEH-JAHORINA (INFOTEH), 2020,
  • [5] Effect of cutting parameters on the surface roughness of titanium alloys using end milling process
    Yusuf, Khairi
    Nukman, Y.
    Yusof, T. M.
    Dawal, S. Z.
    Yang, H. Qin
    Mahlia, T. M. I.
    Tamrin, K. F.
    [J]. SCIENTIFIC RESEARCH AND ESSAYS, 2010, 5 (11): : 1284 - 1293
  • [6] Modeling of machined surface roughness and optimization of cutting parameters in face milling
    Bajic, D.
    Lela, B.
    Zivkovic, D.
    [J]. METALURGIJA, 2008, 47 (04): : 331 - 334
  • [7] Research on the Cutting Fluid Effect on Cutting Force and Surface Roughness in Rotor Milling
    Wang, Jianlu
    Wu, Liangliang
    Zhang, Jun
    Zhao, Wanhua
    Jiang, Yifei
    Shui, Yan
    [J]. HIGH SPEED MACHINING V, 2012, 723 : 50 - +
  • [8] Effect of milling parameters on surface roughness: An experimental investigation
    Sharma, Akash
    Dwivedi, V. K.
    [J]. MATERIALS TODAY-PROCEEDINGS, 2020, 25 : 868 - 871
  • [9] Assessment of Surface Roughness in Milling of Wood with Different Material Temperature and Cutting Parameters
    Korkmaz, Mustafa
    Budakçı, Mehmet
    Kılınç, İzham
    [J]. BioResources, 2024, 19 (04) : 9343 - 9357
  • [10] Optimal cutting parameters for desired surface roughness in end milling Inconel 718
    Wang, Yuanwei
    Zhang, Song
    Li, Jianfeng
    Ding, Tongchao
    [J]. ADVANCES IN ABRASIVE TECHNOLOGY XIII, 2010, 126-128 : 911 - 916
12345