Lattice Boltzmann modeling of injection moulding process

被引：0
|
作者：
Latt, J [1 ]
Courbebaisse, G
Chopard, B
Falcone, JL
机构：
[1] CERN, Dept Comp Sci, CH-1211 Geneva 4, Switzerland
[2] ESP, ERT 10, LRPP, F-01100 Bellignat, France
来源：
CELLULAR AUTOMATA, PROCEEDINGS | 2004年 / 3305卷
关键词：
polymer injection moulding; Hele-Shaw model; mathematical morphology; lattice Boltzmann method; multi-component fluids; numerical simulation;
D O I：
暂无
中图分类号：
TP18 [人工智能理论];
学科分类号：
081104 ; 0812 ; 0835 ; 1405 ;
摘要：
Polymer injection in moulds with complicated shapes is common in todays industrial problems. A challenge is to optimize the mould design which leads to the most homogeneous filling. Current commercial softwares are able to simulate the process only partially. This paper proposes a preliminary study of the capability of a two-fluid Lattice-Boltzmann model to provide a simple and flexible approach which can be easily parallelized, will include correct contact angles and simulate the effect of the positioning of air-holes.
引用
收藏
页码：345 / 354
页数：10
相关论文
共 50 条
  • [1] Numerical Modeling of MuCell® Injection Moulding Process
    Nabialek, Jacek
    Jaruga, Tomasz
    ADVANCES IN MANUFACTURING II, VOL 4 - MECHANICAL ENGINEERING, 2019, : 434 - 447
  • [2] Thermal Dynamic Modeling and Control of Injection Moulding Process
    Seo, Jaho
    Khajepour, Amir
    Huissoon, Jan P.
    AUTONOMOUS AND INTELLIGENT SYSTEMS, 2011, 6752 : 102 - 111
  • [3] A lattice-Boltzmann free surface model for injection moulding of a non-Newtonian fluid
    Chiappini, Daniele
    PHILOSOPHICAL TRANSACTIONS OF THE ROYAL SOCIETY A-MATHEMATICAL PHYSICAL AND ENGINEERING SCIENCES, 2020, 378 (2175):
  • [4] Injection moulding simulation results as an input to the injection moulding process
    Nardin, B
    Kuzman, K
    Kampus, Z
    JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2002, 130 : 310 - 314
  • [5] Visualization of Injection Moulding Process
    Yanev, A. S.
    Dias, G. R.
    Cunha, A. M.
    ADVANCED MATERIALS FORUM IV, 2008, 587-588 : 716 - 720
  • [6] Process control in injection moulding
    Michaeli, W
    Hopmann, C
    Gruber, J
    KUNSTSTOFFE-PLAST EUROPE, 2004, 94 (01): : 20 - 24
  • [7] PROCESS VARIABLES IN INJECTION MOULDING
    GLANVILL, AB
    JARRETT, J
    TRANSACTIONS AND JOURNAL OF THE PLASTICS INSTITUTE, 1966, 34 (112): : 192 - &
  • [8] Polioptimization of an injection moulding process
    Bogucki, Marcin
    Samociuk, Waldemar
    Staczek, Pawel
    Krzysiak, Zbigniew
    PRZEMYSL CHEMICZNY, 2021, 100 (03): : 225 - 229
  • [9] Modeling of the HPC Infiltration Process by means of the Lattice Boltzmann Method
    Chassagne, Romain
    Doerfler, Fabian
    Guyenot, Michael
    2016 17TH INTERNATIONAL CONFERENCE ON THERMAL, MECHANICAL AND MULTI-PHYSICS SIMULATION AND EXPERIMENTS IN MICROELECTRONICS AND MICROSYSTEMS (EUROSIME), 2016,
  • [10] The injection transfer moulding process in comparison to the multi-cavity injection moulding
    Michaeli, W
    Koch, M
    Pfefferkorn, T
    JOURNAL OF POLYMER ENGINEERING, 2006, 26 (2-4) : 197 - 212
12345