Effect of inclusions on fracture behavior of cast and wrought 13% Cr-4% Ni martensitic stainless steels

被引：17

作者：

Foroozmehr, Fayaz ^{[1
]}

Verreman, Yves ^{[1
]}

Chen, Jianqiang ^{[1
]}

Thibault, Denis ^{[2
]}

Bocher, Philippe ^{[3
]}

机构：

[1] Ecole Polytech Montreal, CP 6079,Succ Ctr Ville, Montreal, PQ H3C 3A7, Canada

[2] Inst Rech Hydro Quebec, 1800 Bout Lionel Boulez, Varennes, PQ J3X 1S1, Canada

[3] ETS, Montreal, PQ H3C 1K3, Canada

来源：

ENGINEERING FRACTURE MECHANICS | 2017年 / 175卷

基金：

加拿大自然科学与工程研究理事会;

关键词：

Fracture toughness; Microstructure; Martensitic stainless steels; Inclusions; TRIP effect; TOUGHNESS; MICROSTRUCTURE; STRENGTH;

D O I：

10.1016/j.engfracmech.2017.02.002

中图分类号：

O3 [力学];

学科分类号：

08 ; 0801 ;

摘要：

Microstructures and inclusion characteristics of cast and wrought 13% Cr-4% Ni martensitic stainless steels were related to tensile, fracture toughness J(Ic), and Charpy V-notch absorbed energy. A lower volume fraction of inclusions, a larger number of inclusions smaller than 10 mu m, and a more resistant inclusion type against rupture and against micro-void formation were the key parameters explaining why the wrought steel has better mechanical properties than the cast steel. It has been shown that TRIP effect occurs only in a small region of 6 mm length from the crack plane in J(Ic)-test. (C) 2017 Elsevier Ltd. All rights reserved.

引用

页码：262 / 278

页数：17

共 50 条

[1] On the ductile rupture of 13% Cr-4% Ni martensitic stainless steels
Foroozmehr, Fayaz
Bocher, Philippe
INTERNATIONAL JOURNAL OF FRACTURE, 2020, 224 (01) : 67 - 82
[2] On the ductile rupture of 13% Cr-4% Ni martensitic stainless steels
Fayaz Foroozmehr
Philippe Bocher
International Journal of Fracture, 2020, 224 : 67 - 82
[3] An investigation on fracture toughness of the heat-affected zone in the welded joints of 13% Cr-4% Ni martensitic stainless steels
Foroozmehr, Fayaz
Bocher, Philippe
FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES, 2021, 44 (12) : 3416 - 3430
[4] Residual stress and microstructure in welds of 13%Cr-4%Ni martensitic stainless steel
Thibault, Denis
Bocher, Philippe
Thomas, Marc
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2009, 209 (04) : 2195 - 2202
[5] Effects of Cyclic Heat Treatment on Microstructure and Mechanical Properties of 13%Cr-4%Ni Martensitic Stainless Steel
Jai Singh
S. K. Nath
Journal of Materials Engineering and Performance, 2020, 29 : 2478 - 2490
[6] Effects of Cyclic Heat Treatment on Microstructure and Mechanical Properties of 13%Cr-4%Ni Martensitic Stainless Steel
Singh, Jai
Nath, S. K.
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2020, 29 (04) : 2478 - 2490
[7] Effect of low temperature intercritical heat-treatment on stable crack growth behavior in 13% Cr-4% Ni martensitic stainless steel multipass weldments
Foroozmehr, Fayaz
Bocher, Philippe
ENGINEERING FRACTURE MECHANICS, 2020, 240
[8] Reversed austenite in 0Cr13Ni4Mo martensitic stainless steels
Song, Y. Y.
Li, X. Y.
Rong, L. J.
Li, Y. Y.
Nagai, T.
MATERIALS CHEMISTRY AND PHYSICS, 2014, 143 (02) : 728 - 734
[9] Ni and Mn enrichment effects on reformed austenite: thermodynamical and low cycle fatigue stability of 13%Cr-4%Ni and 13%Cr-6%Ni stainless steels
Godin, Stephane
Hamel-Akre, Johann
Thibault, Denis
Serventi, Alessandra-Maria
Bocher, Philippe
SN APPLIED SCIENCES, 2020, 2 (03):
[10] Investigation of the mechanical stability of reversed austenite in 13%Cr-4%Ni martensitic stainless steel during the uniaxial tensile test
Wang, Pei
Xiao, Namin
Lu, Shanping
Li, Dianzhong
Li, Yiyi
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2013, 586 : 292 - 300

← 1 2 3 4 5 →