Reliability of a high-pressure die cast Al alloy radiator

被引：7
|
作者：
Timelli, Giulio [1 ]
De Mori, Alessandro [1 ]
Haghayeghi, Reza [2 ]
机构：
[1] Univ Padua, Dept Management & Engn, Stradella S Nicola 3, I-36100 Vicenza, Italy
[2] Islamic Azad Univ, Dept Mat Engn, Sci & Res Branch, Tehran, Iran
来源：
ENGINEERING FAILURE ANALYSIS | 2019年 / 105卷
关键词：
Aluminium alloys; Casting defects; Failure analysis; Reliability analysis; Fractography; ALUMINUM-ALLOYS; MN;
D O I：
10.1016/j.engfailanal.2019.06.002
中图分类号：
TH [机械、仪表工业];
学科分类号：
0802 ;
摘要：
The resistance to pressure of a diecast AlSi11Cu2(Fe) alloy radiator has been studied at various holding temperatures. A recently developed method to seal the bottom opening of the radiator element has been presented and its reliability has been even evaluated. Three failure modes are observed during burst testing in the temperature range 40-100 degrees C, i.e. oil leakage at the interface between the radiator element and the plug, rupture of an element and detachment of the plug from the bottom opening. The main failure mechanism is attributed to the fracture of the radiator element, while the detachment of the plug occurs only at higher temperature; very few leakage failures occur. In the considered experimental range, the temperature exposure affects the burst pressure of the radiator. The failure probability of radiator can be described by three-parameter Weibull distribution, which has evidenced the reliability of the described sealing system.
引用
收藏
页码：87 / 97
页数：11
相关论文
共 50 条
  • [1] Effect of pressure cycles and thermal conditions on the reliability of a high-pressure diecast Al alloy heating radiator
    Timelli, Giulio
    De Mori, Alessandro
    Haghayeghi, Reza
    ENGINEERING FAILURE ANALYSIS, 2019, 105 : 276 - 288
  • [2] Effect of position on the tensile properties in high-pressure die cast Mg alloy
    Prakash, D. G. Leo
    Regener, Doris
    Vorster, W. J. J.
    JOURNAL OF ALLOYS AND COMPOUNDS, 2009, 470 (1-2) : 111 - 116
  • [3] Macrosegregation in high-pressure die-cast AM60 alloy
    Lee, SG
    Gokhale, AM
    Patel, GR
    MAGNESIUM TECHNOLOGY 2005, 2005, : 377 - 380
  • [4] Measuring and Modeling Microsegregation in High-Pressure Die Cast Mg–Al Alloys
    Tracy D. Berman
    Zhenjie Yao
    Erin Deda
    Larry Godlewski
    Mei Li
    John E. Allison
    Metallurgical and Materials Transactions A, 2022, 53 : 2730 - 2742
  • [5] Cyclic deformation behavior of an overaged high-pressure die-cast aluminum alloy
    Dash, S. S.
    Liu, Z. Y.
    Zou, Y.
    Li, D. J.
    Zeng, X. Q.
    Li, D. Y.
    Chen, D. L.
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2024, 915
  • [6] Measuring and Modeling Microsegregation in High-Pressure Die Cast Mg-Al Alloys
    Berman, Tracy D.
    Yao, Zhenjie
    Deda, Erin
    Godlewski, Larry
    Li, Mei
    Allison, John E.
    METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2022, 53 (07): : 2730 - 2742
  • [7] Heat Treatment Conditions for High-Performance High-Pressure Die-Cast Al-Si-Cu-Mg Alloy
    Demirtas, Hueseyin
    Karakulak, Erdem
    Babu, Nadendla Hari
    ADVANCED ENGINEERING MATERIALS, 2024, 26 (01)
  • [8] DIE FILLING AND SOLIDIFICATION OF AL-SI ALLOY IN HIGH-PRESSURE DIE-CASTING
    GHOMASHCHI, MR
    SCANDINAVIAN JOURNAL OF METALLURGY, 1993, 22 (02) : 61 - 67
  • [9] The Skin Effect in a High Pressure Die Cast Mg-9%Al Alloy
    Yang, K.
    Nagasekhar, A. V.
    Caceres, C. H.
    MANUFACTURING SCIENCE AND ENGINEERING, PTS 1-5, 2010, 97-101 : 743 - 747
  • [10] Characterization of nanostructures in a high pressure die cast Al-Si-Cu alloy
    Liu, Tao
    Pei, Zongrui
    Barton, Dallin
    Thompson, Gregory B.
    Brewer, Luke N.
    ACTA MATERIALIA, 2022, 224
12345