NUMERICAL AND EXPERIMENTAL FORMING OF AXISYMMETRIC PRODUCTS USING METHODS OF DEEP DRAWING AND FLOW FORMING

被引：1

作者：

Wozniak, D. ^{[1
]}

Hojny, M. ^{[1
]}

Gadek, T. ^{[2
]}

Glowacki, M. ^{[1
,3
]}

机构：

[1] AGH Univ Sci & Technol, Fac Met Engn & Ind Comp Sci, Al A Mickiewicza 30, PL-30059 Krakow, Poland

[2] Met Forming Inst, PL-61139 Poznan, Poland

[3] JKU, Kielce, Poland

来源：

ARCHIVES OF METALLURGY AND MATERIALS | 2015年 / 60卷 / 04期

关键词：

deep drawing; flow forming; FEM modeling; hard-to-deform material; CONVENTIONAL SPINNING PROCESS;

D O I：

10.1515/amm-2015-0453

中图分类号：

TF [冶金工业];

学科分类号：

0806 ;

摘要：

The paper deals with the problem of forming of axisymmetric element. Two-stages process was taken into consideration: deep drawing of metal blank using hydraulic press and the method of elongating flow forming. The contribution presents results of numerical and experimental analyzes. Numerical simulations of both the processes were realized in Krakow at AGH University. Numerical verification of both processes was carried out using finite element models implemented with the help of commercial analysis system on basis of conducted in Poznan experimental shaping tests of Hastelloy C-276 alloy. The tests were aimed to find opportunities and conditions of plastic deformation of the material. This article summarizes example results of both numerical and experimental forming of products made of hard-to-deform material..

引用

页码：2827 / 2832

页数：6

共 50 条

[1] NUMERICAL AND EXPERIMENTAL FORMING OF AXISYMMETRIC PRODUCTS USING FLOW FORMING METHOD FOR HARD-TO-DEFORM MATERIAL
Wozniak, Dawid
Hojny, Marcin
Glowacki, Miroslaw
Gadek, Tomasz
METAL 2015: 24TH INTERNATIONAL CONFERENCE ON METALLURGY AND MATERIALS, 2015, : 452 - 457
[2] Axisymmetric sheet forming of knitted fabric composite by combined stretch forming and deep drawing
Lim, TC
Ramakrishna, S
Shang, HM
COMPOSITES PART B-ENGINEERING, 1999, 30 (05) : 495 - 502
[3] Axisymmetric sheet forming of knitted fabric composite by combined stretch forming and deep drawing
Dept. of Mech. and Prod. Engineering, National University of Singapore, 10 Kent Ridge Crescent, Singapore 119260, Singapore
Compos Part B:Eng, 5 (495-502):
[4] Numerical simulation and experimental examination of forming defects in multi-point deep drawing process
Beglarzadeh, B.
Davoodi, B.
MECHANIKA, 2016, (03): : 182 - 189
[5] Analysis of an axisymmetric deep-drawn part forming using reduced forming steps
Cao, J
Li, SP
Xia, ZC
Tang, SC
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2001, 117 (1-2) : 193 - 200
[6] Forming of Non-axisymmetric Products
Pieszak, M.
Rozmyslowicz, M.
6TH ICAFT-INTERNATIONAL CONFERENCE ON ACCURACY IN FORMING TECHNOLOGY 25TH SFU-SAXON CONFERENCE ON FORMING TECHNOLOGY6TH AUTOMETFORM-INTERNATIONAL LOWER SILESIA-SAXONY CONFERENCE ON ADVANCED METAL FORMING PROCESSES IN THE AUTOMOTIVE INDUSTRY, 2019, 27 : 7 - 12
[7] Simultaneous stretch forming and deep drawing in axisymmetrical sheet forming
Lim, TC
Ramakrishna, S
Shang, HM
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2000, 97 (1-3) : 82 - 87
[8] NUMERICAL MODELING OF DRAWING AND SUPERPLASTIC FORMING
BELLET, M
MASSONI, E
CHENOT, JL
MEMOIRES ET ETUDES SCIENTIFIQUES DE LA REVUE DE METALLURGIE, 1987, 84 (09): : 459 - 459
[9] Experimental and numerical studies on formability of extra-deep drawing steel in incremental sheet metal forming
Kurra, Suresh
Regalla, Srinivasa Prakash
Journal of Materials Research and Technology, 2014, 3 (02) : 158 - 171
[10] Experimental and numerical studies on formability of extra-deep drawing steel in incremental sheet metal forming
Kurra, Suresh
Regalla, Srinivasa Prakash
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T, 2014, 3 (02): : 158 - 171

← 1 2 3 4 5 →