THE RELATIONSHIP BETWEEN DENDRITE ARM SPACING AND COOLING RATE OF Al-Si CASTING ALLOYS IN HIGH PRESSURE DIE CASTING

被引：28
|
作者：
Cho, Jae-Ik [1 ]
Kim, Cheol-Woo [1 ]
机构：
[1] Korea Inst Ind Technol, Kwangju, South Korea
来源：
INTERNATIONAL JOURNAL OF METALCASTING | 2014年 / 8卷 / 01期
关键词：
die casting; aluminum alloy; cooling rate; dendrite arm spacing; solidification; MECHANICAL-PROPERTIES; MICROSTRUCTURE; SOLIDIFICATION;
D O I：
10.1007/BF03355571
中图分类号：
TF [冶金工业];
学科分类号：
0806 ;
摘要：
The effects of cooling rate on the solidification behavior of Al-8.5%Si-3%Cu and Al-11%Si-3%Cu alloys were studied during high pressure die casting (HPDC). The HPDC experiment was conducted by using the dies with three steps for three different cooling rates. Because of both high temperature and pressures involved, it was difficult to obtain the temperature profile directly from HPDC specimen. Therefore, in this study, cylindrical bar castings with different diameter were poured to acquire the cooling curves at the solidification range of 15 degrees C/s up to 100 degrees C/s and then the microstructures were compared to estimate the cooling rate in HPDC. The solidification characteristics including liquidus/solidus temperature and dendrite arm spacing of each alloy and each cooling rate was analyzed and the results showed strong proportional relationship between dendrite arm spacing (DAS) and cooling rate in HPDC. The results were also compared with the actual die casting specimens and MAGMA simulation.
引用
收藏
页码：49 / 55
页数：7
相关论文
共 50 条
  • [1] THE RELATIONSHIP BETWEEN DENDRITE ARM SPACING AND COOLING RATE OF Al-Si CASTING ALLOYS IN HIGH PRESSURE DIE CASTING
    Cho, Jae-Ik
    Kim, Cheol-Woo
    Kim, Young-Chan
    Choi, Se-Weon
    Kang, Chang-Seog
    PROCEEDINGS OF THE 13TH INTERNATIONAL CONFERENCE ON ALUMINUM ALLOYS (ICAA13), 2012, : 1493 - 1498
  • [2] The Relationship between Dendrite Arm Spacing and Cooling Rate of Al-Si Casting Alloys in High Pressure Die Casting
    Jae-Ik Cho
    Cheol-Woo Kim
    International Journal of Metalcasting, 2014, 8 : 49 - 55
  • [3] Characteristics of Al-Si Alloys with High Melting Point Elements for High Pressure Die Casting
    Szymczak, Tomasz
    Gumienny, Grzegorz
    Klimek, Leszek
    Goly, Marcin
    Szymszal, Jan
    Pacyniak, Tadeusz
    MATERIALS, 2020, 13 (21) : 1 - 13
  • [4] INFLUENCE OF DIE CASTING SPEED ON PROPERTIES OF CASTING BASED ON AL-SI ALLOYS
    Ruzbarsky, Juraj
    MM SCIENCE JOURNAL, 2022, 2022 : 6114 - 6122
  • [5] Influence of process parameters on the fluidity of high pressure die-casting Al-Si alloys
    Kim, Young-Chan
    Choi, Se-Weon
    Kim, Cheol-Woo
    Cho, Jae-Ik
    Kang, Chang-Seog
    METALLURGY TECHNOLOGY AND MATERIALS II, 2013, 813 : 171 - 174
  • [6] The Evolution of Dilatant Shear Bands in High-Pressure Die Casting for Al-Si Alloys
    Lu, Jingzhou
    Lordan, Ewan
    Zhang, Yijie
    Fan, Zhongyun
    Wang, Wanlin
    Dou, Kun
    MATERIALS, 2024, 17 (20)
  • [7] Numerical modeling of microstructure evolution and dendrite growth for Al-Si alloy casting during low pressure die casting
    Li, B.
    Xu, Q. Y.
    Liu, B. C.
    PRICM 6: SIXTH PACIFIC RIM INTERNATIONAL CONFERENCE ON ADVANCED MATERIALS AND PROCESSING, PTS 1-3, 2007, 561-565 : 1787 - 1792
  • [8] On the relationship between primary and secondary dendrite arm spacing in continuous casting products
    Cicutti, C
    Boeri, R
    SCRIPTA MATERIALIA, 2001, 45 (12) : 1455 - 1460
  • [9] DIE FILLING AND SOLIDIFICATION OF AL-SI ALLOY IN HIGH-PRESSURE DIE-CASTING
    GHOMASHCHI, MR
    SCANDINAVIAN JOURNAL OF METALLURGY, 1993, 22 (02) : 61 - 67
  • [10] SECONDARY AND TERTIARY DENDRITE ARM SPACING RELATIONSHIPS IN DIRECTIONALLY SOLIDIFIED AL-SI ALLOYS
    GRUGEL, RN
    JOURNAL OF MATERIALS SCIENCE, 1993, 28 (03) : 677 - 683
12345