The Entrance Effect on Gases Flow Characteristics in Micro-tube

被引:7
|
作者
Li, Chengwen [1 ]
Jia, Li [1 ]
Zhang, Tiantian [1 ]
机构
[1] Beijing Jiaotong Univ, Sch Mech & Elect Control Engn, Dept Power Engn, Beijing 100044, Peoples R China
基金
中国国家自然科学基金;
关键词
microchannel; the length of entrance region; entrance effect; constant friction; method of cutting tube; FRICTION FACTOR; SLIP-FLOW; MICROCHANNEL;
D O I
10.1007/s11630-009-0353-5
中图分类号
O414.1 [热力学];
学科分类号
摘要
Entrance region may have important effect on gases flow characteristics in micro-channels. It's concluded in the available papers that the entrance effect causes significant difference. An experimental system of single-phase gas flow characteristics in microchannels was set up. Flow characteristics of nitrogen in PEEK polymer micro-tube (hydraulic diameter is 553 mu m) was studied experimentally. According to the data of nitrogen flow in the micro-tube with the length ranging from 0.1m to 1.524m, it is shown that the friction constant becomes higher when the tube becomes shorter. By using pipe cutting methods, it's confirmed that entrance effect is one of the key factors that cause friction constant higher than conventional theory. It's found that friction constant of fully developed flow is lower than the value predicted by conventional theory in turbulent region. The result indicates that the flow transition occurs at Reynolds number ranging from 1600-2000. The phenomenon of obvious early transition is not found.
引用
收藏
页码:353 / 357
页数:5
相关论文
共 50 条
  • [1] The Entrance Effect on Gases Flow Characteristics in Micro-tube
    Chengwen Li
    [J]. Journal of Thermal Science, 2009, 18 (04) : 353 - 357
  • [2] The entrance effect on gases flow characteristics in micro-tube
    Chengwen Li
    Li Jia
    Tiantian Zhang
    [J]. Journal of Thermal Science, 2009, 18 : 353 - 357
  • [3] SUPERSONIC FLOW AT MICRO-TUBE OUTLET
    Yoshida, Yasuhiro
    Hong, Chungpyo
    Asako, Yutaka
    Suzuki, Koichi
    [J]. IMECE 2009: PROCEEDINGS OF THE ASME INTERNATIONAL MECHANICAL ENGINEERING CONGRESS AND EXPOSITION, VOL 9, PTS A-C, 2010, : 1935 - 1942
  • [4] Gas flow in a short micro-tube
    Hirsch, E. H.
    [J]. VACUUM, 2014, 108 : 1 - 5
  • [5] FLOW AND HEAT TRANSFER OF MICRO-TUBE BANK
    Koizumi, Yasuo
    Katsuta, Atsushi
    Ohtake, Hiroyasu
    [J]. PROCEEDINGS OF THE 8TH INTERNATIONAL CONFERENCE ON NANOCHANNELS, MICROCHANNELS AND MINICHANNELS, 2010, PTS A AND B, 2011, : 551 - 558
  • [6] Size Characteristics of Liposomes Formed in a Micro-Tube
    Suzuki, Hiroshi
    Hamamura, Jun-ya
    Katsuda, Tomohisa
    Komoda, Yoshiyuki
    Katoh, Sigeo
    Usui, Hiromoto
    [J]. JOURNAL OF CHEMICAL ENGINEERING OF JAPAN, 2008, 41 (08) : 739 - 743
  • [7] EXPERIMENTAL INVESTIGATION OF GASEOUS FLOW IN A MICRO-TUBE
    Yoshida, Yasuhiro
    Hong, Chungpyo
    Asako, Yutaka
    Suzuki, Koichi
    [J]. ICNMM 2009, PTS A-B, 2009, : 383 - 389
  • [8] Effect of compressibility on gaseous flows in a micro-tube
    Asako, Y
    Nakayama, K
    Shinozuka, T
    [J]. INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER, 2005, 48 (23-24) : 4985 - 4994
  • [9] Quantitative visualization of micro-tube flow using micro-PIV
    Sugii, Y
    Okamoto, K
    [J]. JOURNAL OF VISUALIZATION, 2004, 7 (01) : 9 - 16
  • [10] Pressure loss of gaseous flow at a micro-tube outlet
    Horii, Y.
    Asako, Y.
    Hong, C.
    Lee, J.
    [J]. PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART C-JOURNAL OF MECHANICAL ENGINEERING SCIENCE, 2011, 225 (C3) : 649 - 657