FIBER ORIENTATION IN INJECTION-COMPRESSION MOLDED SHORT-FIBER-REINFORCED POLYPROPYLENE PARTS

被引：1
|
作者：
Huang, Han-Xiong [1 ]
Yang, Can [1 ]
Li, Kun [1 ]
机构：
[1] S China Univ Technol, Lab Micro Molding & Polymer Rheol, Guangzhou 510640, Guangdong, Peoples R China
来源：
IMECE2009: PROCEEDINGS OF THE ASME INTERNATIONAL MECHANICAL ENGINEERING CONGRESS AND EXPOSITION, VOL 14 | 2010年
关键词：
injection-compression molding; polymer-matrix composites; glass fibers; fiber orientation; NUMERICAL-SIMULATION; THERMOPLASTICS;
D O I：
10.1049/cp.2010.0556
中图分类号：
TH [机械、仪表工业];
学科分类号：
0802 ;
摘要：
Four processing parameters, including compression force, compression time, compression distance, and delay time, were investigated in terms of their effects on the fiber orientation in injection-compression molded (ICM) short-fiber-reinforced polypropylene parts. The results reveal that the fiber orientation pattern in ICM parts is different from that in conventional injection molded parts. Compression force plays an important role in determining the fiber orientation, whereas the effect of compression time can be neglected. Moreover, the fiber orientation changes obviously in the width direction, with most fibers arranging orderly in the flow direction at positions near the mold cavity wall.
引用
收藏
页码：169 / 176
页数：8
相关论文
共 50 条
  • [1] Investigation of Fiber Orientation States in Injection-Compression Molded Short-Fiber-Reinforced Thermoplastics
    Yang, Can
    Huang, Han-Xiong
    Li, Kun
    [J]. POLYMER COMPOSITES, 2010, 31 (11) : 1899 - 1908
  • [2] PREDICTION OF FIBER ORIENTATION IN INJECTION MOLDED PARTS OF SHORT-FIBER-REINFORCED THERMOPLASTICS
    MATSUOKA, T
    TAKABATAKE, JI
    INOUE, Y
    TAKAHASHI, H
    [J]. POLYMER ENGINEERING AND SCIENCE, 1990, 30 (16): : 957 - 966
  • [3] Numerical simulation of three-dimensional fiber orientation in short-fiber-reinforced injection-molded parts
    Han, KH
    Im, YT
    [J]. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2002, 124 (03) : 366 - 371
  • [4] Structural analysis of an injection molded short-fiber-reinforced disk
    Baldwin, JD
    Altan, MC
    Rajamani, K
    [J]. JOURNAL OF MATERIALS PROCESSING & MANUFACTURING SCIENCE, 1997, 6 (02): : 123 - 145
  • [5] Measurment and numerical simulation of three dimensional fiber orientation states in injection-molded short-fiber-reinforced plastics
    Lee, KS
    Lee, SW
    Chung, KS
    Kang, TJ
    Youn, JR
    [J]. JOURNAL OF APPLIED POLYMER SCIENCE, 2003, 88 (02) : 500 - 509
  • [6] FIBER ORIENTATION AND MECHANICAL-PROPERTIES OF SHORT-FIBER-REINFORCED INJECTION-MOLDED COMPOSITES - SIMULATED AND EXPERIMENTAL RESULTS
    GUPTA, M
    WANG, KK
    [J]. POLYMER COMPOSITES, 1993, 14 (05) : 367 - 382
  • [7] Weld strength of injection molded short fiber reinforced polypropylene
    Takayama, Tetsuo
    [J]. MECHANICS OF MATERIALS, 2019, 136
  • [8] Simulation and Optimization of Short Fiber Circumferential Orientation in Short-Fiber-Reinforced Composites Overflow Water-Assisted Injection Molded Tube
    Zhou, Haiying
    Liu, Hesheng
    Kuang, Tangqing
    Jiang, Qingsong
    Chen, Zhixin
    Li, Weiping
    [J]. ADVANCES IN POLYMER TECHNOLOGY, 2019, 2019
  • [9] MEASUREMENTS OF FIBER ORIENTATION IN SHORT-FIBER-REINFORCED THERMOPLASTICS
    OCONNELL, PA
    DUCKETT, RA
    [J]. COMPOSITES SCIENCE AND TECHNOLOGY, 1991, 42 (04) : 329 - 347
  • [10] Flow-induced fiber orientation in injection molded flax fiber reinforced polypropylene
    Aurich, T
    Mennig, G
    [J]. POLYMER COMPOSITES, 2001, 22 (05) : 680 - 689
12345