Exceptionally high strength in Mg-3Al-1Zn alloy processed by high-ratio differential speed rolling

被引：63

作者：

Kim, W. J. ^{[1
]}

Lee, Y. G. ^{[1
]}

Lee, M. J. ^{[2
]}

Wang, J. Y. ^{[3
]}

Park, Y. B. ^{[2
]}

机构：

[1] Hongik Univ, Dept Mat Sci & Engn, Seoul 121791, South Korea

[2] Sunchon Natl Univ, Dept Mat Sci & Engn, Sunchon 540742, South Korea

[3] Natl Dong Hwa Univ, Dept Mat Sci & Engn, Shoufeng 97401, Hualien, Taiwan

来源：

SCRIPTA MATERIALIA | 2011年 / 65卷 / 12期

关键词：

Differential speed rolling; Magnesium alloy; Recrystallization; Texture; Severe plastic deformation; AL-ZN ALLOY; MAGNESIUM ALLOY; MECHANICAL-PROPERTIES; ROOM-TEMPERATURE; GRAIN-SIZE; MG ALLOY; MICROSTRUCTURE; DUCTILITY; TEXTURE;

D O I：

10.1016/j.scriptamat.2011.09.029

中图分类号：

TB3 [工程材料学];

学科分类号：

0805 ; 080502 ;

摘要：

A novel route to prepare an ultrahigh-strength commercial Mg-3Al-1Zn (AZ31) alloy was established by optimizing the processing parameters of high-ratio differential speed rolling (HRDSR). After HRDSR at 423 K followed by immediate water quenching, a grain size of 0.6 mu m was obtained. The ultrafine-grained AZ31 exhibited a very high yield stress of 382 MPa. The effects of the HRDSR conditions on the microstructures and mechanical properties of this alloy were examined and discussed. (C) 2011 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

引用

页码：1105 / 1108

页数：4

共 50 条

[1] Mg-3Al-1Zn alloy strips processed by electroplastic differential speed rolling
Li, X.
Wang, F.
Li, X.
Zhu, J.
Tang, G.
[J]. MATERIALS SCIENCE AND TECHNOLOGY, 2017, 33 (02) : 215 - 219
[2] Texture and mechanical properties of ultrafine-grained Mg-3Al-1Zn alloy sheets prepared by high-ratio differential speed rolling
Kim, W. J.
Lee, H. W.
Yoo, S. J.
Park, Y. B.
[J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2011, 528 (03): : 874 - 879
[3] Fabrication of ultrafine-grained Mg-3Al-1Zn magnesium alloy sheets using a continuous high-ratio differential speed rolling technique
Kim, W. Y.
Kim, W. J.
[J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2014, 594 : 189 - 192
[4] High speed rolling of Mg-3Al-1Zn alloy: texture and microstructure analysis
Sanjari, M.
Farzadfar, S. A.
Utsunomiya, H.
Sakai, T.
Essadiqi, E.
Yue, S.
[J]. MATERIALS SCIENCE AND TECHNOLOGY, 2012, 28 (08) : 928 - 933
[5] Effect of speed-ratio on microstructure, and mechanical properties of Mg-3Al-1Zn alloy, in differential speed rolling
Kim, W. J.
Hwang, B. G.
Lee, M. J.
Park, Y. B.
[J]. JOURNAL OF ALLOYS AND COMPOUNDS, 2011, 509 (34) : 8510 - 8517
[6] Microstructure and superplasticity of the as-cast Mg-9Al-1Zn magnesium alloy after high-ratio differential speed rolling
Kim, Y. S.
Kim, W. J.
[J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2016, 677 : 332 - 339
[7] Dynamic recrystallization mechanisms during high speed rolling of Mg-3Al-1Zn alloy sheets
Su, Jing
Sanjari, Mehdi
Kabir, Abu Syed H.
Jung, In-Ho
Yue, Steve
[J]. SCRIPTA MATERIALIA, 2016, 113 : 198 - 201
[8] Finite element analysis of severe deformation in Mg-3Al-1Zn sheets through differential-speed rolling with a high speed ratio
Ji, Y. H.
Park, J. J.
Kim, W. J.
[J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2007, 454 : 570 - 574
[9] Influence of initial texture on rolling and annealing textures of Mg-3Al-1Zn alloy sheets processed by high temperature rolling
Huang, Xinsheng
Suzuki, Kazutaka
Chino, Yasumasa
Mabuchi, Mamoru
[J]. JOURNAL OF ALLOYS AND COMPOUNDS, 2012, 537 : 80 - 86
[10] Improvement of formability of Mg-3Al-1Zn alloy strip by electroplastic-differential speed rolling
Li, Xiaopei
Wang, Fei
Li, Xiaohui
Tang, Guoyi
Zhu, Jing
[J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2014, 618 : 500 - 504

← 1 2 3 4 5 →