Electromagnetic Force Distribution and Its Effect on the Forming Quality for Numerical Simulation Study of Electromagnetic Flanging of Sheet Metal

被引：0
|
作者：
Huang Pan [1 ]
Huang Liang [1 ,2 ]
Su Hongliang [1 ]
Ma Fei [3 ]
Li Jianjun [1 ]
机构：
[1] Huazhong Univ Sci & Technol, State Key Lab Mat Proc & Die & Mould Technol, Wuhan 430074, Hubei, Peoples R China
[2] Hunan Univ, State Key Lab Adv Design & Mfg Vehicle Body, Changsha 410082, Hunan, Peoples R China
[3] China Aerosp Sci & Technol Corp, Changzheng Machinery Factory, Chengdu 610100, Sichuan, Peoples R China
来源：
RARE METAL MATERIALS AND ENGINEERING | 2019年 / 48卷 / 09期
关键词：
electromagnetic flanging; electromagnetic force; marginal accumulation effect; forming quality;
D O I：
暂无
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
Based on electromagnetic flanging process of aluminum alloy sheet metal, numerical simulation was conducted to investigate the distribution characteristics of the electromagnetic force and the influence of geometry parameters on the electromagnetic force distribution, and then the influence of the electromagnetic force distribution on the forming quality of workpieces was revealed. The results show that in the process of electromagnetic flanging of aluminum alloy sheet metal, the marginal accumulation effect of the electromagnetic force is produced due to the existence of the precast hole. The aperture of the sheet metal and the inner diameter of the forming coil can affect the distribution of electromagnetic force by changing the ratio of the projection area to the coil area. With the decrease of the ratio of the projection area to the coil area, the marginal accumulation effect of the electromagnetic force becomes more prominent, and the electromagnetic force density of the hole edge increases. Materials of the corner area flow more significantly under the circumstance of the uniform electromagnetic force distribution; meanwhile higher forming height and smaller edge reduction rate can be obtained after forming, which means more uniform thickness distribution of the deformation area and better forming quality of workpiece.
引用
收藏
页码：2987 / 2993
页数：7
相关论文
共 20 条
  • [1] [Anonymous], CHIN J NONFERROUS ME
  • [2] Chen XW, 2015, RARE METAL MAT ENG, V44, P514
  • [3] Chu Hongyan, 2003, J MECH ENG, V39, P62
  • [4] Cowper G.R., 1957, Small Bus. Econ., V31, P235, DOI DOI 10.21236/AD0144762
  • [5] Electromagnetic pulse-assisted incremental drawing of aluminum cylindrical cup
    Fang, Jinxiu
    Mo, Jianhua
    Cui, Xiaohui
    Li, Jianjun
    Zhou, Bo
    [J]. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2016, 238 : 395 - 408
  • [6] Research on plastic flow behaviors for hole flanging part of aluminum alloy with large complicated profiles by electromagnetic forming
    Huang, Liang
    Luo, Wenyong
    Liu, Xianlong
    Li, Jianjun
    [J]. Jixie Gongcheng Xuebao/Journal of Mechanical Engineering, 2013, 49 (24): : 24 - 29
  • [7] An elasto-plastic finite element analysis of the sheet metal stretch flanging process
    Huang, Yuung-Ming
    [J]. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2007, 34 (7-8): : 641 - 648
  • [8] Deformation behavior of a 2219 Al alloy
    Kaibyshev, R
    Sitdikov, O
    Mazurina, I
    Lesuer, DR
    [J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2002, 334 (1-2): : 104 - 113
  • [9] Numerical investigations on springback characteristics of aluminum sheet metal alloys in warm forming conditions
    Kim, Hong Seok
    Koc, Muammer
    [J]. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2008, 204 (1-3) : 370 - 383
  • [10] Liu D., 2010, THESIS
12