EMPIRICAL MODELLING OF CUTTING FORCE COMPONENTS IN TURNING

被引：0
|
作者：
Oleg, Ryabov [1 ]
Kano, Seisuke [1 ]
Sawada, Hiroyuki [1 ]
Herwan, Jonny [1 ]
机构：
[1] Natl Inst Adv Ind Sci & Technol, Adv Mfg Res Inst, 1-2-1 Namiki, Tsukuba, Ibaraki, Japan
来源：
PROCEEDINGS OF THE 2018 IEEE INTERNATIONAL CONFERENCE ON ADVANCED MANUFACTURING (IEEE ICAM) | 2018年
关键词：
cutting force; turning; force sensor;
D O I：
暂无
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
Dimensional and dynamical components of cutting force signals measured during the turning of grey cast iron, aluminum and steel allows are analyzed. The empirical models built on the basis of the experimental data approximation are presented. Similarity of some models obtained for the cases of different materials processing is shown and discussed.
引用
收藏
页码：7 / 10
页数：4
相关论文
共 50 条
  • [1] Evaluation of cutting force uncertainty components in turning
    Axinte, DA
    Belluco, W
    De Chiffre, L
    [J]. INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2001, 41 (05): : 719 - 730
  • [2] Cutting-force components in turning by tools with no cutting tip
    Filippov A.V.
    Filippova E.O.
    Chazov P.A.
    [J]. Russian Engineering Research, 2016, 36 (12) : 1040 - 1043
  • [3] Modelling and Analysis of Cutting Force Components in Turning Process of Commercially Pure Titanium Grade 2
    Habrat, Witold
    Sala, Monika
    Krolczyk, Jolanta B.
    Markopoulos, Angelos P.
    Legutko, Stanislaw
    [J]. ADVANCES IN MANUFACTURING II, VOL 4 - MECHANICAL ENGINEERING, 2019, : 317 - 328
  • [4] Assessment of Metal Wear in Turning on the Basis of Components of the Cutting Force
    Lapshin V.P.
    Turkin I.A.
    Khristoforova V.V.
    [J]. Russian Engineering Research, 2020, 40 (09): : 797 - 800
  • [5] Examination and modelling of the influence of cutting parameters on the cutting force and the surface roughness in longitudinal turning
    Bajic, Drazen
    Lela, Branimir
    Cukor, Goran
    [J]. STROJNISKI VESTNIK-JOURNAL OF MECHANICAL ENGINEERING, 2008, 54 (05): : 322 - 333
  • [6] MODELLING OF MICRO-TURNING PROCESS BASED ON CONSTANT CUTTING FORCE
    Vukelic, D.
    Kanovic, Z.
    Sokac, M.
    Santosi, Z.
    Budak, I
    Tadic, B.
    [J]. INTERNATIONAL JOURNAL OF SIMULATION MODELLING, 2021, 20 (01) : 146 - 157
  • [7] PREDICTION OF SPECIFIC CUTTING FORCE AND CUTTING FORCE RATIO IN TURNING
    LEE, BY
    TARNG, YS
    [J]. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 1994, 41 (01) : 71 - 82
  • [8] Artificial neural network modelling of cutting force components in milling
    Zagorski, Ireneusz
    Kulisz, Monika
    Semeniuk, Aleksandra
    [J]. II INTERNATIONAL CONFERENCE OF COMPUTATIONAL METHODS IN ENGINEERING SCIENCE (CMES'17), 2017, 15
  • [9] Cutting force predictive modelling of hard turning operation using fuzzy logic
    Sharma, Vikas
    Kumar, Pawan
    Misra, Joy Prakash
    [J]. MATERIALS TODAY-PROCEEDINGS, 2020, 26 : 740 - 744
  • [10] Determination of cutting force coefficients with mechanistic and numerical modelling in micro turning process
    Hascelik, Ahmet
    Aslantas, Kubilay
    [J]. JOURNAL OF THE FACULTY OF ENGINEERING AND ARCHITECTURE OF GAZI UNIVERSITY, 2022, 37 (01): : 229 - 246
12345