Fatigue of AlSi10Mg specimens fabricated by additive manufacturing selective laser melting (AM-SLM)

被引：223
|
作者：
Uzan, Naor Elad [1 ]
Shneck, Roni [1 ]
Yeheskel, Ori [2 ]
Frage, Nachum [1 ]
机构：
[1] Ben Gurion Univ Negev, Dept Mat Engn, POB 653, IL-8410501 Beer Sheva, Israel
[2] Nucl Res Ctr Negev, Dept Mat, POB 9001, IL-84190 Beer Sheva, Israel
来源：
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING | 2017年 / 704卷
关键词：
Additive manufacturing; AlSi10Mg; Fatigue; Fractography; Tensile properties; Fracture toughness; Hot isostatic pressing; HIGH-CYCLE FATIGUE; MECHANICAL-PROPERTIES; HEAT-TREATMENT; MICROSTRUCTURE; BEHAVIOR; EVOLUTION;
D O I：
10.1016/j.msea.2017.08.027
中图分类号：
TB3 [工程材料学];
学科分类号：
0805 ; 080502 ;
摘要：
The fatigue resistance of AM-SLM AlSi10Mg samples built in the Z direction after various heat treatments was investigated. Specimens were tested in the as-built (AB) condition, after stress relief (SR) treatment and after SR and hot isostatic pressing (HIP) at either 250 degrees C or 500 degrees C. The AB machined and polished specimens displayed the highest fatigue limit (S-f = 125 MPa, N-f = 10(7) cycles). SR and HIP cycles decrease the yield strength, hardness and fatigue limit. The SR and HIP treatment at 500 degrees C resulted in the lowest fatigue resistance due to significant microstructural changes. A relation between the yield stress and fatigue resistance was established, Linear elastic fracture mechanics were employed for evaluating fracture surface morphology. Based on the results of fracture surface characterization, values of the critical stress intensity factor (K-cr) for AM-SLM AlSi10Mg specimens after various heat treatments were estimated.
引用
收藏
页码：229 / 237
页数：9
相关论文
共 50 条
  • [1] On the effect of shot-peening on fatigue resistance of AlSi10Mg specimens fabricated by additive manufacturing using selective laser melting (AM-SLM)
    Uzan, Naor Elad
    Ramati, Shlomo
    Shneck, Roni
    Frage, Nachum
    Yeheskel, Ori
    [J]. ADDITIVE MANUFACTURING, 2018, 21 : 458 - 464
  • [2] High-temperature mechanical properties of AlSi10Mg specimens fabricated by additive manufacturing using selective laser melting technologies (AM-SLM)
    Uzan, Naor Elad
    Shneck, Roni
    Yeheskel, Ori
    Frage, Nachum
    [J]. ADDITIVE MANUFACTURING, 2018, 24 : 257 - 263
  • [3] RESIDUAL STRESSES OF AlSi10Mg FABRICATED BY SELECTIVE LASER MELTING (SLM)
    Karolus, M.
    Maszybrocka, J.
    Stwora, A.
    Skrabalak, G.
    [J]. ARCHIVES OF METALLURGY AND MATERIALS, 2019, 64 (03) : 1011 - 1016
  • [4] Microstructure and Properties of AlSi10Mg Fabricated by Selective Laser Melting (SLM)
    Bai, P. K.
    Zhao, Z. Y.
    Li, J.
    Wu, L. Y.
    Liang, M. J.
    Tan, L.
    Liao, H. H.
    [J]. LASERS IN ENGINEERING, 2019, 44 (1-3) : 157 - 167
  • [5] Fatigue Strength of an AlSi10Mg Alloy Fabricated by Selective Laser Melting
    M. V. Gerov
    E. Yu. Vladislavskaya
    V. F. Terent’ev
    D. V. Prosvirnin
    O. S. Antonova
    A. G. Kolmakov
    [J]. Russian Metallurgy (Metally), 2019, 2019 : 392 - 397
  • [6] Fatigue Strength of an AlSi10Mg Alloy Fabricated by Selective Laser Melting
    Gerov, M. V.
    Vladislavskaya, E. Yu.
    Terent'ev, V. F.
    Prosvirnin, D. V.
    Antonova, O. S.
    Kolmakov, A. G.
    [J]. RUSSIAN METALLURGY, 2019, 2019 (04): : 392 - 397
  • [7] A study on cavitation erosion behavior of AlSi10Mg fabricated by selective laser melting (SLM)
    Zou, J.
    Zhu, Y.
    Pan, M.
    Xie, T.
    Chen, X.
    Yang, H.
    [J]. WEAR, 2017, 376 : 496 - 506
  • [8] Acoustic Emission and Deep Learning for the Classification of the Mechanical Behavior of AlSi10Mg AM-SLM Specimens
    Barile, Claudia
    Casavola, Caterina
    Pappalettera, Giovanni
    Kannan, Vimalathithan Paramsamy
    Mpoyi, Dany Katamba
    [J]. APPLIED SCIENCES-BASEL, 2023, 13 (01):
  • [9] Additive manufactured AlSi10Mg samples using Selective Laser Melting (SLM): Microstructure, high cycle fatigue, and fracture behavior
    Brandl, Erhard
    Heckenberger, Ulrike
    Holzinger, Vitus
    Buchbinder, Damien
    [J]. MATERIALS & DESIGN, 2012, 34 : 159 - 169
  • [10] Influence of defect size on the fatigue resistance of AlSi10Mg alloy elaborated by selective laser melting (SLM)
    Ngnekou, Julius N. Domfang
    Nadot, Yves
    Henaff, Gilbert
    Nicolai, Julien
    Ridosz, Lionel
    [J]. 3RD INTERNATIONAL SYMPOSIUM ON FATIGUE DESIGN AND MATERIAL DEFECTS (FDMD 2017), 2017, 7 : 75 - 83
12345