Determination of cutting-condition-independent coefficients and runout parameters in ball-end milling

被引：25
|
作者：
Ko, JH [1 ]
Cho, DW [1 ]
机构：
[1] Pohang Univ Sci & Technol, Dept Mech Engn, Pohang 790784, Kyungbuk, South Korea
来源：
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY | 2005年 / 26卷 / 11-12期
关键词：
ball-end milling; cutting force coefficients; runout; size effect;
D O I：
10.1007/s00170-004-2121-8
中图分类号：
TP [自动化技术、计算机技术];
学科分类号：
0812 ;
摘要：
This paper presents a systematic and practical method for determining cutting-condition-independent coefficients in ball-end milling. An approach for estimating the runout offset and its location angle is also described based on a single cutting force measurement. An in-depth analysis of the characteristics of these cutting coefficients, which can be determined from only a few test cuts, is provided. The size effect is also modelled, including the characteristics of the ball-end mill geometry, and incorporated into the cutting force model. This method of estimating the 3D ball-end milling force coefficients was tested experimentally for various cutting conditions and gave excellent cutting force predictions. Also, the estimated values of the runout offset agreed well with the measurements.
引用
收藏
页码：1211 / 1221
页数：11
相关论文
共 50 条
  • [1] Determination of Cutting-Condition-Independent Coefficients and Runout Parameters in Ball-End Milling
    Jeong Hoon Ko
    Dong-Woo Cho
    [J]. The International Journal of Advanced Manufacturing Technology, 2005, 26 : 1211 - 1221
  • [2] Investigation of the cutting force coefficients in ball-end milling
    Liu, XW
    Cheng, K
    Webb, D
    Longstaff, AP
    Widiyarto, MH
    Jiang, XQ
    Blunt, L
    Ford, DG
    [J]. LASER METROLOGY AND MACHINE PERFORMANCE VI, 2003, : 45 - 54
  • [3] A mechanistic model of cutting forces in micro-end-milling with cutting-condition-independent cutting force coefficients
    Lee, Han Ul
    Cho, Dong-Woo
    Ehmann, Kornel F.
    [J]. JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME, 2008, 130 (03): : 0311021 - 0311029
  • [4] A chatter free calibration method for determining cutter runout and cutting force coefficients in ball-end milling
    Yao, Zhen-Qiang
    Liang, Xin-Guang
    Luo, Lei
    Hu, Jun
    [J]. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2013, 213 (09) : 1575 - 1587
  • [5] The identification of the cutting force coefficients for ball-end finish milling
    Xiaojun Lin
    Gang Wu
    Yun Zhang
    Tong Cui
    Bo Zhang
    Pengchen Sun
    [J]. The International Journal of Advanced Manufacturing Technology, 2019, 102 : 4121 - 4135
  • [6] The identification of the cutting force coefficients for ball-end finish milling
    Lin, Xiaojun
    Wu, Gang
    Zhang, Yun
    Cui, Tong
    Zhang, Bo
    Sun, Pengchen
    [J]. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2019, 102 (9-12): : 4121 - 4135
  • [7] Identification of Cutting Force Coefficients in Different Cutting Edges of Ball-End Milling Cutter
    Li, Bai-Chun
    Wang, Zhen-Yu
    Zhang, Bin
    Wang, Wan-Shan
    [J]. Dongbei Daxue Xuebao/Journal of Northeastern University, 2019, 40 (09): : 1316 - 1322
  • [8] Study on Effects of Cutter Radial Runout and Deformation on Cutting Force in Ball-End Hard Milling
    Zhao, Xingfa
    Liu, Xianli
    Xiao, Fei
    Wang, Yanxin
    Jiang, Yancui
    [J]. APPLICATION OF DIAMOND AND RELATED MATERIALS, 2011, 175 : 284 - 288
  • [9] A simplified approach for determining empirical cutting force coefficients for ball-end milling
    Azeem, A
    Feng, HY
    Wang, LH
    [J]. TRANSACTIONS OF THE NORTH AMERICAN MANUFACTURING RESEARCH INSTITUTION OF SME, VOL XXXI, 2003, 2003, : 121 - 128
  • [10] ANALYSIS OF CUTTING FORCES IN BALL-END MILLING
    CHIANG, ST
    TSAI, CM
    LEE, AC
    [J]. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 1995, 47 (3-4) : 231 - 249
12345