Effect of tempering on the wear characteristics of induction-hardened SPS5 steel

被引：0
|
作者：
Kim, M. H. [1 ]
Rhee, K. Y. [2 ]
Hong, J. S. [3 ]
Ham, Y. S. [3 ]
机构：
[1] Kyung Hee Univ, Grad Sch Mech Engn, Yongin 449701, South Korea
[2] Kyung Hee Univ, Sch Mech & Ind Syst Engn, Ctr Media Transport Syst, Yongin 449701, South Korea
[3] Korea Railrd Res Inst, Syst Interface Res Team, Uiwang 437757, South Korea
来源：
PROGRESSES IN FRACTURE AND STRENGTH OF MATERIALS AND STRUCTURES, 1-4 | 2007年 / 353-358卷
关键词：
induction-hardening; wear; friction; tempering; ball-on-disk;
D O I：
10.4028/www.scientific.net/KEM.353-358.835
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
In this study, the tempering effect on the wear characteristics of induction-hardened SPS5 steel was investigated. For this purpose, three tempering conditions were applied to control the hardness and microstructure of heat-treated SPS5 steel. Ball-on-disk wear tests have been performed using zircornia balls on the tempered specimens to determine the variation of wear characteristics. The results showed that friction coefficient decreased with increasing hardness for induction-hardened SPS5 steel. This seems to occur because real contact area between specimen and mating ball was affected by the specimen hardness. Also, we observe the wear type changes from the plowing wear to the adhesive wear as the hardness increases and the adhesive wear particles act as an obstacle to the transmission of the force of friction, reducing the coefficient of friction and the wear rate.
引用
收藏
页码：835 / +
页数：2
相关论文
共 50 条
  • [1] Experimental investigation on the mechanical behavior of high-frequency induction-hardened mild carbon, SPS5 steel
    Kim, M. H.
    Rhee, K. Y.
    Paik, Y. N.
    Hong, J. S.
    Ham, Y. S.
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2008, 485 (1-2): : 31 - 38
  • [2] METALLURGICAL CHARACTERISTICS OF INDUCTION-HARDENED STEEL
    POYNTER, JW
    TRANSACTIONS OF THE AMERICAN SOCIETY FOR METALS, 1946, 36 : 165 - 209
  • [3] Residual stresses and wear properties of induction-hardened medium carbon steel
    Liu, Q. C.
    Cao, Y. J.
    Sun, J. Q.
    He, Q. K.
    Tan, Y. L.
    Li, B. M.
    Xie, K.
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART J-JOURNAL OF ENGINEERING TRIBOLOGY, 2019, 233 (10) : 1554 - 1564
  • [4] Effect of Microstructural Banding on the Fatigue Behavior of Induction-Hardened 4140 Steel
    Hayne, M. L.
    Anderson, P. I.
    Findley, K. O.
    Vantyne, C. J.
    METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2013, 44A (08): : 3428 - 3433
  • [5] Effect of Microstructural Banding on the Fatigue Behavior of Induction-Hardened 4140 Steel
    M. L. Hayne
    P. I. Anderson
    K. O. Findley
    C. J. Van Tyne
    Metallurgical and Materials Transactions A, 2013, 44 : 3428 - 3433
  • [6] Fractography of induction-hardened steel fractured in fatigue and overload
    Santos, CG
    Laird, C
    MATERIALS CHARACTERIZATION, 1997, 39 (01) : 25 - 41
  • [7] EFFECT OF RESIDUAL-STRESS ON FATIGUE-STRENGTH OF INDUCTION-HARDENED STEEL
    HAYAMA, T
    BULLETIN OF THE JSME-JAPAN SOCIETY OF MECHANICAL ENGINEERS, 1975, 18 (125): : 1194 - 1200
  • [8] Effect of Different Microstructures on Surface Residual Stress of Induction-Hardened Bearing Steel
    Lu, Shao-Quan
    Chiu, Liu-Ho
    METALS, 2024, 14 (02)
  • [9] The analysis of fretting wear in forced-in joint with the induction-hardened shaft
    Kowalski S.
    Tribologia, 2021, 38 (1-2): : 11 - 21
  • [10] Dry sliding wear of an induction-hardened, high-silicon medium-carbon microalloyed steel
    Ceschini, Lorella
    Martini, Carla
    Morri, Alessandro
    TRIBOLOGY INTERNATIONAL, 2015, 92 : 493 - 502
12345