Investigation of Interfacial Fracture Behavior on Injection Molded Parts

被引：3

作者：

Fischer, Matthieu ^{[1
]}

Ausias, Gilles ^{[2
]}

Kuehnert, Ines ^{[1
]}

机构：

[1] Leibniz Inst Polymerforsch Dresden eV, Polymer Proc Dept, Dresden, Germany

[2] UBS, Lab Ingn Mat Bretagne, Lorient, France

来源：

PROCEEDINGS OF PPS-31: THE 31ST INTERNATIONAL CONFERENCE OF THE POLYMER PROCESSING SOCIETY | 2016年 / 1713卷

关键词：

Injection molding; morphology; interface; weld line; fracture;

D O I：

10.1063/1.4942276

中图分类号：

O59 [应用物理学];

学科分类号：

摘要：

In this study the interfacial morphology of different polymers joined by various assembly injection molding (AIM) technologies were discussed. Melt streams were injected successively using tools with core-back or rotation techniques. To compare bulk specimen strength and weld line strength, the fracture behavior of different specimen scales and thin sections were investigated. An in-situ SEM tensile test and a new thin section testing device which is used in polarized (transmitted) light microscopy were used to observe specimen failure. The effects of processing on spherulitic structures were linked to bonding strength and mechanical properties.

引用

页数：5

共 50 条

[1] Investigation of compression behavior of PE/EVA foam injection molded parts
Spina, Roberto
[J]. PROCEEDINGS OF THE 20TH INTERNATIONAL ESAFORM CONFERENCE ON MATERIAL FORMING (ESAFORM 2017), 2017, 1896
[2] An Investigation of Weldline Strength in Injection Molded Rubber Parts
Chookaew, Watcharapong
Mingbunjurdsuk, Jirachai
Jittham, Pairote
Ranong, Nuchanat Na
Patcharaphun, Somjate
[J]. 10TH ECO-ENERGY AND MATERIALS SCIENCE AND ENGINEERING SYMPOSIUM, 2013, 34 : 767 - 774
[3] Post-ejection cooling behavior of injection molded parts
Moller, J
Carlson, M
Alterovitz, R
Swartz, J
[J]. CONFERENCE PROCEEDINGS AT ANTEC '98: PLASTICS ON MY MIND, VOLS I-3: VOL I; PROCESSING, VOL II; SPECIAL AREAS, VOL III; MATERIALS, 1998, 44 : 525 - 529
[4] Shrinkage behavior and optimization of injection molded parts studied by the Taguchi method
Chang, TC
Faison, E
[J]. POLYMER ENGINEERING AND SCIENCE, 2001, 41 (05): : 703 - 710
[5] Experimental assessment and optimization of shrinkage behavior of injection molded polycarbonate parts
Azdast, Taher
Hasanzadeh, Rezgar
[J]. MATERIALS RESEARCH EXPRESS, 2019, 6 (11)
[6] The influence of level of interfacial healing on the weld-line strengths of injection molded parts
Huang, Chung-Ching
Wu, Yu-Yi
Chang, Hui-Tang
Yang, Yi-Jen
[J]. JOURNAL OF POLYMER ENGINEERING, 2012, 32 (6-7) : 365 - 378
[7] NEW DESIGN OF INJECTION MOLDED PARTS
BEALL, G
[J]. KUNSTSTOFFE-GERMAN PLASTICS, 1990, 80 (08): : 911 - 914
[8] Thermoelasticity of Injection-Molded Parts
Turk, Janez
Svensek, Daniel
[J]. POLYMERS, 2023, 15 (13)
[9] Morphology Distribution in Injection Molded Parts
Liparoti, Sara
Salomone, Rita
Speranza, Vito
Pantani, Roberto
[J]. POLYMERS, 2024, 16 (03)
[10] Optimizing injection-molded parts
Deitz, D
[J]. MECHANICAL ENGINEERING, 1996, 118 (10) : 89 - 90

← 1 2 3 4 5 →