The use of mirrors during an assembly task: a study of ergonomics and productivity

被引:6
|
作者
Lutz, TJ [1 ]
Starr, H [1 ]
Smith, CA [1 ]
Stewart, AM [1 ]
Monroe, MJ [1 ]
Joines, SMB [1 ]
Mirka, GA [1 ]
机构
[1] N Carolina State Univ, Dept Ind Engn, Ergon Lab, Raleigh, NC 27695 USA
关键词
assembly task; EMG; posture; productivity;
D O I
10.1080/00140130120518
中图分类号
T [工业技术];
学科分类号
08 ;
摘要
Industrial assembly tasks often require awkward, sustained neck and/or shoulder postures that can lead to increased musculoskeletal discomfort and reduced productivity. The aim of this study was to investigate the effects of mirror and periscope visual aids as ergonomic interventions designed to eliminate awkward postures of the cervicobrachial region during assembly tasks. Participants simulated a simple assembly task by using a cordless screwdriver to drive screws into a pre-tapped aluminium block. Trials of 15 min were run for each of four distinct assembly workstation configurations: industry standard (in-line screwdriver, work at elbow height, no visual aid); pistol grip (pistol grip screwdriver, work at shoulder height, no visual aid); mirror (in-line screwdriver, work at elbow height, single mirror visual aid); and periscope (in-line screwdriver, work at elbow height, two-mirror visual aid system). Muscular activity, discomfort, body posture, productivity and operator subjective assessment were recorded to determine the effects of the visual aid interventions. The results show that when comparing the interventions to the industry standard condition, there was a 45% reduction in average cervical erector spinae activity, a 90% reduction in average neck flexion angle and a 72% reduction in neck discomfort with the interventions. When comparing these interventions to the pistol grip condition there was an 80% reduction in activity of the dominant side deltoid, a 92% reduction in shoulder flexion angle and an 81% decrease in shoulder discomfort with the interventions. Productivity was greatest in the industry standard configuration followed by the pistol grip (9% lower), the periscope (13% lower) and the mirror (23% lower) configurations. A follow-up study that compared the productivity of the periscope configuration with that of the industry standard configuration showed that within a 4-h work period this productivity differential decreased by over 33%.
引用
收藏
页码:215 / 228
页数:14
相关论文
共 50 条
  • [1] Ergonomics in parallelized car assembly: A case study, with reference also to productivity aspects
    Lindholmen Development, Department of Injury Prevention, Chalmers University of Technology, Göteborg, Sweden
    不详
    不详
    APPL. ERGON., 2 (101-110):
  • [2] Ergonomics in parallelized car assembly: A case study, with reference also to productivity aspects
    Kadefors, R
    Engstrom, T
    Petzall, J
    Sundstrom, L
    APPLIED ERGONOMICS, 1996, 27 (02) : 101 - 110
  • [3] A participatory and integrative approach to improve productivity and ergonomics in assembly
    De Looze, MP
    Van Rhijn, JW
    Van Deursen, J
    Tuinzaad, GH
    Reijneveld, CN
    PRODUCTION PLANNING & CONTROL, 2003, 14 (02) : 174 - 181
  • [4] Incorporating Ergonomics Evaluation in Assembly and Disassembly of Repetitive Task: Focusing on load task
    Dawal, Siti Zawiah Md.
    Ghazilla, Raja Ariffin bin Raja
    Zadry, Hilma Raimona
    Widia, Mirta
    Abdullah, Nor Suliani
    ADVANCES IN MANUFACTURING SCIENCE AND ENGINEERING, PTS 1-4, 2013, 712-715 : 2879 - 2883
  • [5] The right track for ergonomics in assembly work? A comparison between two production concepts on ergonomics and productivity
    Groenesteijn, L
    De Groot, MD
    Van Rhijn, JW
    De Looze, MP
    Tuinzaad, GH
    QUALITY OF WORK AND PRODUCTS IN ENTERPRISES OF THE FUTURE, 2003, : 289 - 292
  • [6] New methodological framework to improve productivity and ergonomics in assembly system design
    Battini, D.
    Faccio, M.
    Persona, A.
    Sgarbossa, F.
    INTERNATIONAL JOURNAL OF INDUSTRIAL ERGONOMICS, 2011, 41 (01) : 30 - 42
  • [7] Task allocation for improved ergonomics in Human-Robot Collaborative Assembly
    El Makrini, Ilias
    Merckaert, Kelly
    De Winter, Joris
    Lefeber, Dirk
    Vanderborght, Bram
    INTERACTION STUDIES, 2019, 20 (01) : 102 - 133
  • [8] Ergonomics task analysis in technical training: Case study
    Bourassa, MJ
    Robert, JM
    Naud, Y
    SAFETY SCIENCE, 1996, 23 (2-3) : 145 - 146
  • [9] Mathematical modelling for process design of walking worker assembly line in productivity and ergonomics perspectives
    Al-Zuheri, Atiya
    Xing, Ke
    Luong, Lee
    International Journal of Industrial and Systems Engineering, 2013, 14 (01) : 104 - 137
  • [10] Task allocation strategies considering task matching and ergonomics in the human-robot collaborative hybrid assembly cell
    Cai, Min
    Liang, Rensheng
    Luo, Xinggang
    Liu, Chunlai
    INTERNATIONAL JOURNAL OF PRODUCTION RESEARCH, 2023, 61 (21) : 7213 - 7232